Search results

  1. jeffnoel

    Problems encountered while attempting to break-in a new cam

    She's alive!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! <div align="center"> <object type="application/x-shockwave-flash" data="http://feat.putfile.com/flow/putfile.swf?videoFile=New-cam-broken-in" height="349" width="420" align="middle"> <param name="movie"...
  2. jeffnoel

    74 mustang

    The front header panel and the gas cap location are the easy ones to spot. Header on the 74 is about 3" wide 75-78 abot 1.5" wide. The gas cap on the 74 is lower than 75+ also. But even without the title the VIN will tell you what year it is.
  3. jeffnoel

    Problems encountered while attempting to break-in a new cam

    Finally some good news, I got it started today but could only let it run for about 5-6 minutes at 2000-2500 rpm because it started overheating. I had the cap off the radiator to verify flow and before we got it on I lost about 1/2 of the coolant and the temp went to about 210-220 and I shut it...
  4. jeffnoel

    Problems encountered while attempting to break-in a new cam

    So I checked a couple things out. I removed the valve covers and rotated the engine by hand and verified the standard 15426378 firing order and set the timing at 10 degrees on the balancer with the magnetic pickup lined up firing on #1. I also checked my MSD box and coil using the instructions...
  5. jeffnoel

    Problems encountered while attempting to break-in a new cam

    80 GPH is the lowest flow mechanical fuel pump Holley makes. The others are 110, 130, and 170 GPH.
  6. jeffnoel

    Problems encountered while attempting to break-in a new cam

    That's kinda what I'm thinking. Even though I'm pretty sure I've got a bad pump (new Holley 80 GPH pump should be here tomorrow) I thought it would have fired since the fuel bowls were filled and even a little gas shot into the throttle bores as a last ditch attempt. Thanks for the timing...
  7. jeffnoel

    Problems encountered while attempting to break-in a new cam

    I thought about being 180 and spun the distibutor and when I did it backfired so I put it back were it was.
  8. jeffnoel

    Problems encountered while attempting to break-in a new cam

    I tried starting the Mustang after the winter mods and it won't start. I have gas, 5 gallons added to the recently cleaned and sealed gas tank. Fuel filers are clean and I have spark, I checked by pulling the #1 plug and grounding it to verify spark at the plug. I prefilled the fuel bowls in the...
  9. jeffnoel

    5.0 swap

    With the TC you also get an 8.8 rear with discs already.
  10. jeffnoel

    74 mustang

    The standard Cobra front spoiler might the rear won't without some work. You could put a King Cobra front spoiler and rear wheel spats on it maybe a rear wing from a T-bird.
  11. jeffnoel

    5.0 swap

    So do you want EFI to reduce emmisions? Getting it smogged as an EFI is going to cost you.
  12. jeffnoel

    H1 H3?

    Stock lamps neither. if your ordering projecters they will come with bulbs usually all H1s.
  13. jeffnoel

    5.0 swap

    Where are you located?
  14. jeffnoel

    74 mustang

    You may be able to put on a chin spoiler, not sure with the 74 as is a little different than the 75-78s. Wheels are a challenge but can be done if you measure twice before you cut. You can also put an aftermarket rear wing on it also. What would you like to do to it? This one or...
  15. jeffnoel

    Coolent overflow

    Just sharing "MY" experience, since the factory tank didn't have a drain like the Canton and I haven't had problems in 2+ years.
  16. jeffnoel

    Coolent overflow

    I replaced the nipple with a plug on my Canton and haven't had any problems in 2 years.
  17. jeffnoel

    New Steeda Idler Pulleys

    Yes 2 smooth ans the PS pulley. He doesn't make a ribbed pulley anymore for the Mustang. I know it's on his website, but if you check his website was last updated in 2004.
  18. jeffnoel

    New Steeda Idler Pulleys

    The stand alone one works great, the one on the factory tensioner not so well. But does fit great on the one from NAPA and it gave me the opportunity to polish the tensioner.
  19. jeffnoel

    throttle body coupler

    OK I wish they had them in something other than blue, black and red. Got a link to something in yellow?
  20. jeffnoel

    New Steeda Idler Pulleys

    He goes by the name Wazee on eBay
Top Bottom
Back
Forums
Menu