Search results

  1. BIG-MAC

    crosswind intake?

    OK thanks...
  2. BIG-MAC

    crosswind intake?

    sure...check my garage
  3. BIG-MAC

    crosswind intake?

    What's a Crosswind?
  4. BIG-MAC

    Fun with +0mm offset Bullitt wheels

    No. A 9" wide wheel will not fit on the front. The 17x9 w/+24 with a 1" spacer will stick out approximately 1.25" further than the front wheels shown in the pics of my car above.
  5. BIG-MAC

    Fun with +0mm offset Bullitt wheels

    Thanks...in those pics the car still has 18x10's and 295/35's on the back. This rubbed so I went smaller instead of raising the car up. You can also try here for late model replica wheels www.mustangtuning.com The wheel backspacing you described is a 9" wheel that will not fit the front...
  6. BIG-MAC

    Fun with +0mm offset Bullitt wheels

    My 68 has 18x8 front wheels with 5.42" back spacing plus a 1/4" spacer for a total backspace of approx 5.16". They fit ok without the spacer except the wheel lip rubbed the UCA's (GW) near full lock. On the back I run 18x9 with 5.94" backspacing and no spacers.
  7. BIG-MAC

    Wheels for my 1969 Fastback

    The FR500 will fit. My 68 copue has 18x8 (narrowed 18x9 +36)on the front with a 245/40 tire and a 1/4" spacer to keep the rim off of the upper control arm at full lock. The GW front springs have 1 full coil removed. Your 69 might have enough room for the 18x9 without narrowing. On the...
  8. BIG-MAC

    How tall is your air cleaner?

    I run a 2.5" K&N inside a repro hi-po lid and base. The intake is a vic jr with a 1" spacer and a demon carb. Don't know yet if it will clear my 67 Shelby style hood as its out being painted. If not then I can reduce the spacer and/or change to a drop base.
  9. BIG-MAC

    I've officially decided to go turbo on my 68

    amen brother
  10. BIG-MAC

    whats a good cam for dragracing and street its going in a 351

    If you are running an auto trans with a stock converter and gears (2.80-3.00) thats probably all you want or the low end off the line performance will really suck...been there done that. If you plan on or already have a higher than stock stall converter, or a 4 spd and/or 3.50+ gears I would...
  11. BIG-MAC

    Shelby fiberglass hood

    I bought a glass 67 Shelby style hood for my coupe but resold it since it was crap. Then I bought (eBay) an original steel hood with the 67 Shelby style scoop "professsionally" bonded to it that was " ready for paint". And after an additional 20 hours of work it is finally ready for paint.
  12. BIG-MAC

    numbers on 351 block ?

    The only thing I about that number is the D2 means the year 1972. That is a good block made before the main webs were shrunk in 74(?)
  13. BIG-MAC

    Post up your roll bar/cage pics

    I guess I should have checked and searched first...thanks guys.:shrug:
  14. BIG-MAC

    Let me see your trunk

    Hi 67coupe351W...I noticed the rear down bar from the roll bar in your trunk picture. I just started a new thread regarding roll bars for 67/68 coupes. Please check it out and help if you can. Thanks!
  15. BIG-MAC

    Post up your roll bar/cage pics

    I am almost done with my coupe and am to the point where I need to put the seatbelts in. But since a bit of irresponsible driving may be in my near future the stock belts do not seem to be the smart way to go. Plus I want to replace the stock buckets with Scat Procars, so a 4 pt harnesses would...
  16. BIG-MAC

    Let me see your trunk

    Dam thats nice...I am going to have to get a set.
  17. BIG-MAC

    Let me see your trunk

  18. BIG-MAC

    Post Your Stang!

    sorry...my second post in this thread. I am trying to get the pics to show in the message instead of attachments.
  19. BIG-MAC

    Newbie with pics

    I figured it was time to broaden my horizons:SNSign:
  20. BIG-MAC

    Post Your Stang!

    almost done....
Top Bottom
Back
Forums
Menu