Search results

  1. 94tang

    Steve's Megasquirt/tunerstudio Help Thread

    Added 5 to Initial Idle Values and it seem to help some.....I think surging is still my biggest nemesis, if i tap the throttle it clears up for a few min.
  2. 94tang

    Steve's Megasquirt/tunerstudio Help Thread

    Thanks Steve, will do when I get home later this evening
  3. 94tang

    Steve's Megasquirt/tunerstudio Help Thread

    I've had my mspnp for a couple of months now on my '94 Gt and learned a lot reading this forum, also a big shout out to a91what for help with my tune. What setting do i need to adjust to keep the idle from dropping when coming to a stop? The car doesnt die but comes close to it.
  4. 94tang

    New mspnp for my 94 gt....have some basic ?'s

    I hooked all the factory stuff back up and reset the timing to 10* BTDC. I then reinstalled the MS and using the trigger wizard ONLY and fixed timing, i reset the base timing. What i ended up with was an offset of 52* using the trigger wizard. My timing tables look normal now and the car runs...
  5. 94tang

    New mspnp for my 94 gt....have some basic ?'s

    Tried pulling the SPOUT just to see what would happen and the car died.....
  6. 94tang

    New mspnp for my 94 gt....have some basic ?'s

    Bucking was probably the wrong term....sputtering is prob closer.....afr was right around target 13.5 I would gladly get a datalog for you, if i knew how......im very new to all this
  7. 94tang

    New mspnp for my 94 gt....have some basic ?'s

    So i followed the instructions for "setting timing"....everything matched up with the MS....which is not what i was wanting to see. Below 2500rpms the car runs ok(still have some fine tuning to do), above say 3000rpms, the car bucks and sputters, backfiring through the exhaust sometimes. I drove...
  8. 94tang

    New mspnp for my 94 gt....have some basic ?'s

    So there is no "base" timing to set?.....the numbers in the timing table, is that actual timing or an adder?.....thanks for the help
  9. 94tang

    New mspnp for my 94 gt....have some basic ?'s

    Ok, so setting base timing with factory ecu, you pull the "pill", rotate the dizzy to 14* ( for 93 octane) tighten dizzy, reinstall pill...how do you do this with ms/ts......everything ive read so far (had the pnp for a week now) says to use trigger wizard and set it to 20.....so the base timing...
  10. 94tang

    Airbag light.....?

    Dont remember....think it was a 94
  11. 94tang

    Airbag light.....?

    Replaced a bad clockspring
  12. 94tang

    PARTING OUT 94 GT

    How much for both roof rail moldings shipped to 37660?
  13. 94tang

    Rockers Arms

    Put em on my car and couldnt tell any difference....may show on a dyno but not seat of the pamts
  14. 94tang

    PARTING OUT 94 GT

    I need both roof rails and attaching hardware.Whats the price w/shipping to 37660?
  15. 94tang

    1994 mustang gt memory codes...

    we all have'em from time to time
  16. 94tang

    1994 mustang gt memory codes...

    yeah i got what you meant...however there is still no sensor in the upper intake....its in the lower intake on the drivers side......no coolant runs thru the upper.....:D
  17. 94tang

    1994 mustang gt memory codes...

    done a KOER test and while doing it the CEL went out....?.....no 212 or 118 code tho i got a 332(EGR flow) which can be expected.....guess ill leave it alone and see if it does it again
  18. 94tang

    1994 mustang gt memory codes...

    there is no sensor in the upper intake...i replaced the one that is in the heater tube.....also checked the SPOUT connector and it was ok....and got a CEL today going home....car seemed to lack a little power....not much,just enough to feel
  19. 94tang

    1994 mustang gt memory codes...

    Keep getting these codes.....car runs fine and no CEL.... 118-Coolant temp. sensor above maximum voltage...(replaced 7-4-11) 212-Ignition module circuit failure?SPOUT circiut grounded looks like the car wouldnt run according to the last code (212)....any ideas?
  20. 94tang

    cruise control dead

    clockspring
Top Bottom
Back
Forums
Menu