Search results

  1. ky_kneedragger

    Timing chain cover

    i've actually done some research and you can not use romeo heads on a windsor block or windsor heads on a romeo block
  2. ky_kneedragger

    romeo-windsor

    the heads are also different,like you cant use romeo heads on a windsor block.
  3. ky_kneedragger

    timing

    it dont really matter what its made of,after so much rubbing from the chains anything is gonna wear out! some last longer than others,and i know a few people thats had the same problem i have.
  4. ky_kneedragger

    romeo-windsor

    lol i did too...but i thought i knew a lil about these motors...i was wronnngggg
  5. ky_kneedragger

    timing

    my car had about 70k on it and the chains actually wore through the guides and in the tensioners!!!! i had noticed a ticking noise about 6 months b4 i found the problem and it kinda sounded like a throwout bearing,and it didn't do it all the time! i think it's a crappy setup on ford's part.the...
  6. ky_kneedragger

    p0133 and p0153 codes HELP!!!

    as far as the sensors being too far back,u can buy threaded bungs and have them welded on the back primary tube and put the sensor there.thats what i did with mine.you have to take the headers back off though
  7. ky_kneedragger

    romeo-windsor

    my 00 gt is knocking like crazy,so a friend of mine from a ford dealer gave me a motor from a f150. it was pulled due to carbon build up on the pistons and the owner went the cheaper route and got a junkyard motor rather paying the dealer labor rates for the original motor.Anyway all i have to...
  8. ky_kneedragger

    Timing chain cover

    so u can use romeo heads on a windsor block and vise versa? but the heads gaskets are diff.i have a romeo motor with the heads off and i put an old head gasket from my 00' gt windsor and the ports wouldnt line up the same?
  9. ky_kneedragger

    Timing chain cover

    i didnt think the heads from a romeo would work on a windsor.
  10. ky_kneedragger

    engine swap!

    i recently changed the crank in my motor and it called for the 6 bolt flywheel and a friend of mine gave his factory clutch,pressure plate,and flywheel from his 06 gt...so i already have that ...i was worried bout the different wiring plugs,sensors...ect. thanks for the info
  11. ky_kneedragger

    engine swap!

    i was wondering what i'd have to do to install a romeo motor into my 00' gt? it has the original Windsor motor and once again it's knocking like crazy!!! is all the wiring the same?computer???i know the clutch is different but i'm not worried bout that????
  12. ky_kneedragger

    bad miss!!! help!!

    i just got my car back together about a lil over a week ago and i added a typhoon intake,l/t headers with the cams i already had.i also got rid of the egr and blocked off the vacum lines.it keeps throwing 2 egr codes along with muliple misfire,system lean bank 1 and sometimes 2,and cylinder...
  13. ky_kneedragger

    idle problem

    the guy who bout my tuner didnt even use it,and the guy b4 him just used it to change gear ratio and rev limiter.so its all stock!! i keep gettin dtc codes on my car and it's saying i have cylinder misfire on 2,3,4,and now 8...and system lean on bank 1..i cant feel any mis in the car when i...
  14. ky_kneedragger

    idle problem

    i have the xcalibrator 2,it says its a strategy flash..i dont know much about these damn tuners..lol. the model # is 9415A if that helps...is this a decent tuner? i know it's a few years old b/c the guy that bought it new2 or 3 years ago and it has been through 3 more people since.since i added...
  15. ky_kneedragger

    idle problem

    well thats just it,i haven't tuned it yet.just recently got it put together.i wanna try to go to modular depot and get it dyno tuned.how much is the tuner u were talking about?i need a cable to connect my tuner to my pc! any ideas what i could do myself with my programmer?change spark at diff...
  16. ky_kneedragger

    idle problem

    i dont think my tuner can do that!i have the sct tuner...
  17. ky_kneedragger

    idle problem

    after i rev my car or pull up to a stop light...ect it idles high for bout 3 seconds b4 it straightens up to the normal idle speed!i'm running comp cams xe278 ah's with l/t headers and typhoon intake..i have everything the cams recommend and other than the idle problem it runs great!someone told...
  18. ky_kneedragger

    How many thrust bearings

    no,these are called thrust washer or thrust bearing...they are on the crankshaft at the rear of the motor
  19. ky_kneedragger

    How many thrust bearings

    how many thrust bearings does a windsor 4.6 use???my new bearing kit came with 3 and i think thats all that came out 2 months ago.it looks like it would need a 4th 1 but i'm not sure...help me out somebody!!!
  20. ky_kneedragger

    shorty's or long tubes

    ya know i think i might just go with long tubes...lol
Top Bottom
Back
Forums
Menu