Search results

  1. OonDeanisS

    Post pics of how your foxbody currently sits

    minus the rainguards...
  2. OonDeanisS

    MSD 6Al Where to put?

    im glad you asked this, as ive been wondering the exact same thing. i just got a 6al-2, wish me luck! haha
  3. OonDeanisS

    valve cover breathers

    heres a pic...
  4. OonDeanisS

    valve cover breathers

    gt-40 intake, and yea, but it still has that plate under the fill hole... :shrug:
  5. OonDeanisS

    valve cover breathers

    yea, its not the air filter, its thick black sludgy dry oil caked on everything from that port on the TB down into the intake. definitely coming from the valve cover hose. So... should i replace the cap or is that normal? i could get an oil separator but ive only seen them used on the PCV...
  6. OonDeanisS

    valve cover breathers

    no, its clearly coming from my TB hose coming from the passenger side valve cover. When i look into the TB, i can see the oil build up coming from that port, and it has basically covered the entire upper intake and TB in black gunk. Unless you're saying its coming up from the PCV and...
  7. OonDeanisS

    valve cover breathers

    so why then does my valve cover to throttle body hose let oil into my TB and intake if the air is supposed to be going from the TB into the VC? It looks like my intake is sucking vacuum on my valve cover and pulling oil up into the throttle body, so my entire intake and EGR system is coated in...
  8. OonDeanisS

    ID this connector, and help with cold start stumble needed

    try unplugging your MAF and see if it runs better... if it does, you may have a problem there, or if it gets worse, in another sensor.i have the same issue, and mine runs better without the MAF plugged in... im just saving money for a new one.
  9. OonDeanisS

    is it a bad MAF?

    thanks, ill go get a vac guage this weekend. and a new egr valve and regulator solenoid lol.
  10. OonDeanisS

    is it a bad MAF?

    codes 91 and 33. i had 91 and 31, then replaced my EVP, and now its 91 and 33. edit: i had to use an analog voltmeter to dump the codes, as the CEL never came on.
  11. OonDeanisS

    is it a bad MAF?

    ive never seen my check engine light go on. Even when i dumped the codes. Mine was made by massairsystems which i was told was the Pro-M sensor after they were bought out by another company a few years ago. I plugged it in today after removing the bent part and cleaning the wires, and it...
  12. OonDeanisS

    is it a bad MAF?

    well, it was new. so it didnt need to be cleaned, and the connector is free of corrosion. i havent checked for continuity in the connector, but i did search and find some info, just not exactly my situation. More importantly, i just removed it and noticed i bent the plastic in by...
  13. OonDeanisS

    is it a bad MAF?

    my car runs like crap- backfiring thru intake, running "flat" and losing power, and bouncing idle. I disconnected the MAF, and bingo! car runs like a champ! except it smokes and doesnt idle very well this way. I also smell fuel. But my question is this... will a new MAF make the car run like...
  14. OonDeanisS

    EGR KOER code 33

    old post... but the answer is to jumper a test light between the vref and the sigrtn while the car is in diagnostic mode (jumper wire from the Self test input connector to the signal return pin, which is pin#2). turn key to run but not start, and watch for a flash. if you see it, the solenoid...
  15. OonDeanisS

    89 GT 5.0 backfiring into the intake

    did you get it fixed? what was the outcome?
  16. OonDeanisS

    no code 11

    so i ran a KOEO and came up with 4, then 91, 31. no 11? I keep reading that this means i have "computer or wiring problems" but what does THAT mean? how can i fix this? any help greatly appreciated!
  17. OonDeanisS

    1990 5.0 runs fine when cold but terrible when hot

    i didnt get a code 11, just 4, then about a quarter of a sweep, which i didnt count as a "sweep" then, i got 21,91,31. the second time i did it, i got a 4, then 91,31.
  18. OonDeanisS

    Auto lite 3924 doesn't fit?

    thank you.
  19. OonDeanisS

    Auto lite 3924 doesn't fit?

    I have gt40 iron heads, and I bought auto lite 3924s but they don't thread in... They look identical to my old plugs but these won't thread into the hole... I don't get it. Do I need to cut off the aluminum washers or something? The old ones thread in and out fine, but those are NGK platinums...
  20. OonDeanisS

    Quick Question: Stock Serpentine Belt Length?

    on a 5.0, its a 91" K6 belt. -old topic, but for future reference.
Top Bottom
Back
Forums
Menu