Search results

  1. Dbeck002

    I need this to beat ricers, They are fast..

    My flux capacitor boosts at 2000 rpm!!1 hahah pwnt...:eek:
  2. Dbeck002

    drivability with H/C/I 302, full bolt ons.

    Lift and duration alone arent what cause the bucking, its more the lobe seperation angle. Basically the intake and valve are open at the same time causing the intake to blow out the exhaust at LOW RPM, at high RPM the exhaust aids intake by scavenging. So with a 112 LSA i get the bucking at low...
  3. Dbeck002

    drivability with H/C/I 302, full bolt ons.

    Ok first of all your setup sounds fine. You MAY have a vacuum leak, check everywhere 10 times. I personally think it is your TPS sensor, my car had serious idle issues until that was adjusted and i have the same cam you do. As for the cam, it bucks under 1500 rpm because thats the nature...
  4. Dbeck002

    What caused this carnage?

    Seems like the force exerted on the ring lands came from the bottom up. I would imagine the ring gap was to tight and caused the tip ends on the piston ring to want to push on eachother, only to go nowhere but break the weakest part of the piston at that point, the ring land directly above the...
  5. Dbeck002

    T5 rebuild question: dog ring or synchronized gears

    You should see a lot more power with that once its tuned right.
  6. Dbeck002

    5.0 Resto... Reliable?

    dude this thread is 2 years old...
  7. Dbeck002

    dyno results chart-any new ones or updates to this one??

    Also, what was the ambient air temp during the dyno? It wouldnt make a HUGE difference but as long as all the dynos were performed under nearly the same conditions than that list looks pretty darn accurate. You can add mine if you want. Mod list is on the bottom of my site and dyno is...
  8. Dbeck002

    A little video from 2005.

    Damn skippy!!
  9. Dbeck002

    No compression...Valve Seal or Piston ring

    It doesnt sound like a piston ring, even with very poor rings you will see compression build and then drop slowly as air escapes through the worn rings. Reading zero means there is a large gap somewhere coming from one of the valves. Is there a lot of carbon buildup on your valves?
  10. Dbeck002

    look at what my throttle body did

    Just get a 70mm TB... broken parts mean performance upgrades!!
  11. Dbeck002

    Adding clutch disk to 31 spline traction-lock.

    This question is for a friend who is not near a computer right now and needs to know this. He has a 31 spline ford traction lok unit that he bought new one year ago. He runs slicks and when doing a burnout one wheel spins faster than the other, he wants to know if you can add one more disk to...
  12. Dbeck002

    race gas question?????

    Rick, does it burn slower as well? Or both?
  13. Dbeck002

    carb swap...

    Fox fan how is your car not practical anymore? Its still practically stock but with gears. With all my mods and i still drive it 70 miles a day, 5 days a week and only now im considering buying another car. I probably wont because the stang is running strong. Is that T5 too much power...
  14. Dbeck002

    eprom burners, companys with software and laptops!

    My question is this, would you gain anything by breaking down the EEC unit as opposed to tuning it via PMS, Tweecer or megasquirt? Will one even get anything worthy out of such headache when it can be accomplished by one of the three above tuning devices. EDIT: I forgot to add, units...
  15. Dbeck002

    My gauges make noise!!!

    Yea its live-able now... thanks guys..
  16. Dbeck002

    My gauges make noise!!!

    Hissin, I turned the car on and went down under the dash, played with the copper line and noticed that in some positions the rattle is reduced. So i zip tied the sh1t out of the copper line, tied it to the water gauge line to keep it stiff. This seems to work and the noise has been almost...
  17. Dbeck002

    My gauges make noise!!!

    Ok guys, i put my ear to the gauge and it seems to rattle from inside the gauge. Have you guys had any problem like this? The gauges work fine so we cant assume they are broken and something is hanging around in there. I might stuff the A pillar molding with foam or something. Grr...
  18. Dbeck002

    Why does Ford exhaust sound the best ?

    Yea everyone tells me that fords always sound better than chevy's.. I dont know why either :shrug:
  19. Dbeck002

    Vibration damper questions.....

    The puller should attach to the inner section of the damper. Go back and look, im pretty sure the inner hub is what is being pulled on.
  20. Dbeck002

    Steeda "drag" sway bar.

    Mega bite Jrs, granatelli uppers, lakewood 50/50, pinion snubber, subframes. im looking to get the steeda swaybar because i want to restore some handling, right now it has not front sway bar and it gets annoying.
Top Bottom
Back
Forums
Menu