Search results

  1. 82boy

    fuel system for carb options

    well i did what your doing once what i did was use the factory pick up and just ran a rubber line from it to the pump where i used a fitting i found in the hardware store. on the alum line i would like to discourage you from using it. its hard to work extreamly hard to double wall...
  2. 82boy

    which driveshaft saftey loop

    i use a metco i think its got the best fit mounting and its lighter than most cost a bit more but you get what you pay for
  3. 82boy

    whoo knows alot about carbs??

    i would have to agree a 600 is right for your combo. i would start out at holley's factory jetting. then go from thier. on spacers they are a tunning tool. and need to be looked at as such. you may loos power using a carb spacer. its a tool to use. your performer intake is a duel plane...
  4. 82boy

    What year starter to get for upgrade to my 88

    also pa gives you the wiring kit to change over. not like its a big deal but its nice
  5. 82boy

    What year starter to get for upgrade to my 88

    94 and up stangs my 95 f15 has one. both autozone and advances have them instock for 120 plus core and tax looking at 160 something out the door.they are remanufactored starters. my advice is if you can wait go to pa performance. http://www.paperformance.com/ you get a brand new starter...
  6. 82boy

    help with 60' times!!!

    what size dr are they? what tire pressure are you running? how long do you heat them up in the box? whats your pinion angle at? the lowering springs are killing it it dont have enough front end travel. yes the front end greatly has an efect on the rear end.a set of 70/30 struts would help. 4cly...
  7. 82boy

    race buckets what the best way to instal

    anyone have any picts the seats are 1/2 inch slimer on each side. the ony way i could bolt the brackets to the seat is i would have to drill new holes in the floor pan and i dont think that would be safe the factory bolts are renforced in the floor pan for safty reasons. how are you guys doing...
  8. 82boy

    1.6 or 1.72 rockers whats the difference

    i would run 7/16 studs they are much stronger. hope your not using factory heads they are psdistool mount.
  9. 82boy

    race buckets what the best way to instal

    like the subject says"race buckets what the best way to instal" we finaly took the jump and bought a set of polly high back race buckets. what the best way to instal them i figger that i would use my old tracks off my old seats the race buckets are a hair slimer so what the best rout of making...
  10. 82boy

    Radiator and fan help needed

    i have a afco rad just like yours works great got to rember its not a direct replacment so some fit isues will be thier i had vern house (pa performance)make me a upper suport i used a focus eltric twin fan and i took my old hose to advanced and looked through everything they had till i found a...
  11. 82boy

    How to Adjust the Pinion Angle

    lots in your 60 foot times
  12. 82boy

    How to Adjust the Pinion Angle

    read this it should help you out http://www.baselinesuspensions.com/info/pinionangle.htm
  13. 82boy

    Which heads TFS/AFR

    this also depends on your cam. they use a diferent piston as far as valve notches when larger cams are used as far as mm&ff i dont belive everything i read.
  14. 82boy

    Need Next Suspension Mod Help?!?!?

    tires will help the most .i think you would be greatly disapointed will everything on your list i am no suspention expert. thier is nothing wrong with a factory set up 4 cly springs up front 70/30 struts and gt springs in the back plently of people go fast on that set up. using a bit of ballast...
  15. 82boy

    Which heads TFS/AFR

    i would have to agree 100% you have a good combo i dont know that you would pick up that much hp from switching heads. as far as the question goes i like tfs over afr personal preference if you dead set on changing out heads i would go with the tw heads they have great potential if you what...
  16. 82boy

    engine swap

    yes you need a trany to the 4cly tranys are not strong enough but we mate the trany to the engine when we put them it makes it easier. as far as autos go you can get a aod or a c4 to work.
  17. 82boy

    engine swap

    it all depends on your mechinal ability. if you fell comfortable doing the work i think its a better way to go. i dont know what you got invested in your 4cyl but people want an arm and a leg for a factory v8 car nowadays i only paid a couple hundred bucks for all the 4clys i ever had. the...
  18. 82boy

    Which heads TFS/AFR

    tw heads work great with a blower or turbo. i dont know if it will clear with your e cam something you will have to reasearch. but with 1.7's i think you would have to change pistons. but i think any head you run you might have ptv clearence with any head with the 1.7 rockers and e cam. i...
  19. 82boy

    engine swap

    the swap it self is simple done it a few times. the 4 cly and v8 share the same k member no problem thier the engine drops right in. now for the part that need replaced depending on year most 4cly cars have a single hump trany x member so you will have to get a double hump x member to run...
  20. 82boy

    Which heads TFS/AFR

    i am sure i will get flamed for this i like tfs heads much better. depends on your combo I have seen amazing things out of a set of twisted wedge heads. i run high ports and love them. i also think the tw r head is the greatest thing since sliced bread. if i did not have so many pasrts left over...
Top Bottom
Back
Forums
Menu