cams

  1. Y

    Cams in Ca?

    Hey all! I have a 2002 Mustang GT 5 speed with 3.73 gears, a cold air intake, a 91 octane bama tune, an SLP loudmouth catback exhaust, and a throttle body. I really want to put in some cams but don’t know if I should have some supporting mods first. I was looking at stage 2 comp cams because it...
  2. C

    Blown engine swapping npi and pi???

    Blew my motor on my 2000 gt. I got a good lead on a 1996 4.6 npi motor. I also have a good lead on stage 3 comp cams and springs for 96-04 2v engines. What would make the best sense/work? Getting the heads ported on the 96 engine and using my intake and other stuff off my current mustang plus...
  3. J

    Cam questions

    I have a 98 GT and I am getting ready to do a PI swap. While the heads are out I figure it would be a good time to do the cams and springs. My question is what will work best for a stock bottom end stage I or Stage 2? I have heard there are clearance issues with stage 3 and up. Looking to keep...
  4. J

    Cooling fan kills motor

    I have a 2002 Mustang Gt with comp cams 270 and a few other bolt ons. Whenever i start the car it idles and drives fine, until the fan comes on. If the car is sitting and idling and the fan kicks on for temperature, it’ll instantly kill the motor. If I’m driving and the fan is on and i come to a...
  5. D

    Can I Use S550 Exhaust Cams In 11-14?

    Hi all, I've got a new crate engine in my 2011 Coyote. It's got the 2015 cams/Phasers/chains etc. I've been told I need to change back to 11-14 VCT for the engine to run properly. I keep getting bank 1 and 2 intake cams over retarded codes. I've heard that the S550 exhaust cams can be used...
  6. M

    Best Cam For My Set Up?

    I know this has been beat to death in the past but it's now 2016, companies have come an gone an a lot has changed since the old threads on this. I'm looking for the best cam for my PI swapped 96 Gt. I have a PI intake, LTs, X pipe, cat delete, throttle body & plenum, and full CAI system. I'm...
  7. SOC_DOC32

    Expired For Sale, Aluminator Short Block, 03 Cobra Fr500 Heads, And Enginless Project Car

    If anyone is interested I am parting ways with my (ZERO "0" Miles on it) 4.6L Aluminator Iron sleeved DOHC Engine assembly. It is a built for boost via Centrifugal Style Supercharger (I do not have a Supercharger for this car) stuffed with a 298ci STROKER rotating assembly from Livernoise...
  8. Mike N

    Engine Best Cams For Performance (4.6)

    In your opinion,what are your go to cams to recommend based solely on performance gain. Cyber Monday is upon us and I'm going to be ordering a set of cams. Her specs are below.
  9. Last Call Racing Cammed All Motor S197 Walk Around - Comp 127600

    Last Call Racing Cammed All Motor S197 Walk Around - Comp 127600

    GoPro - Jonathan of http://www.LastCallRacing.com All Motor 3V S197 walk around and exhaust clip. The car has a 4.75L 11:1 MMR1000 Shortblock. It's an awesome motor that LOVES to rev, unlike the 5.0 strokers that are too much stroke. Ported Heads, Comp 127600 SPR stage 3 Cams, that make...
    • LastCallRacing
    • Media item
    • 111 127600 150 2006 mustang gt camm 2007 mustang gt camm 46 46l 475l all burnout call camaro cammed cams cl cobra comp corvette drag drag race drag racing exhaust gopro headers heads hellion intake jba lascallracing last lastcallracingsd lethal mile mmr1000 motor mustang mustang gt nitrous novi or paxton ported race racer racing s197 shortblock shot slicks spr stage stage3 street supercharged supra turbo turbocharged turndowns vortech wheel stand wheelie xpipe
    • Comments: 0
    • Category: Sound Clips
Top Bottom
Forums
Menu