• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

1985 5.0 Cylinder ?

  • Thread starter Thread starter 32ratrod
  • Start date Start date Feb 24, 2008
3

32ratrod

New Member
Nov 26, 2007
3
0
1
Feb 24, 2008
#1
  • Feb 24, 2008
  • #1
I measured the cylinders in my 302 and they are 4.005" is that enough to worry about boring and honing or is there a more economical way to go about closing up the gap. I am a college student and I dont want to spend the money if I dont have to. Thank You.
 

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
Feb 25, 2008
#2
  • Feb 25, 2008
  • #2
well if you bore it then you will need over sized pistons. honing normally just removes a miniumal amount of material so sometimes you are fine with a new set of springs... go get a 87 trough 92 engine.. better heads and you have eye browed pistions so you can run a bigger cam without valve to piston clearence issues.. jusy my opinion
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Feb 25, 2008
#3
  • Feb 25, 2008
  • #3
ditto on the 87-93 engine or better yet would be an explorer motor. If you shop around they can all be found for a pretty decent price and the explorer will give you at least 80hp over stock.
 
3

32ratrod

New Member
Nov 26, 2007
3
0
1
Feb 25, 2008
#4
  • Feb 25, 2008
  • #4
I have the roller motor and I am putting the GT-40 iron heads on it. The pistons that are in it already do have the eyebrow reliefs in it. So since the cylinders measure 4.005" I should be good if I buy a new set of rings?
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Feb 25, 2008
#5
  • Feb 25, 2008
  • #5
93 LX said:
well if you bore it then you will need over sized pistons. honing normally just removes a miniumal amount of material so sometimes you are fine with a new set of springs... go get a 87 trough 92 engine.. better heads and you have eye browed pistions so you can run a bigger cam without valve to piston clearence issues.. jusy my opinion
Click to expand...

stykthyn said:
ditto on the 87-93 engine or better yet would be an explorer motor. If you shop around they can all be found for a pretty decent price and the explorer will give you at least 80hp over stock.
Click to expand...


Just FYI but all of the 302s from at least '82 to '85 had forged pistons with valve reliefs...they were the exact same pistons as the forged pieces in the later '87+ pistons before they switched to hyper pistons. I believe the lack of reliefs in the '86 was to aid in combustion due to the crappy heads. E7s are a tad better than E5s though and you'll gain roughly :05 compression with switching to them from E5s.
 

88mouse

New Member
Apr 18, 2007
630
0
0
Mooresville nc
Feb 26, 2008
#6
  • Feb 26, 2008
  • #6
32ratrod said:
I have the roller motor and I am putting the GT-40 iron heads on it. The pistons that are in it already do have the eyebrow reliefs in it. So since the cylinders measure 4.005" I should be good if I buy a new set of rings?
Click to expand...

Mic your pistons and see what they are at. When you take a block to be bored you have to take the piston so they know what size they need to bored each cyl. Same thing with what you're doing. But five thousands of and inch you should be ok. If you get a set of file fit ring you will be in good shape.
 

Fast63

New Member
Sep 20, 2007
717
0
0
Feb 26, 2008
#7
  • Feb 26, 2008
  • #7
yeah, the 85 5.0 roller engine is the same thing so keep it. How much ridge is there in there bore? It should still read 4.000 at the very top of the bore because the rings do not go up that high and there is minute to no wear there from the piston. If there is no ridge in the bore, maybe you measured wrong? When I took my 85 5.0 roller engine apart the first time with 150k miles on it, it still looked like brand new. There was no ridge and basically no wear, so maybe it's fine.
 
3

32ratrod

New Member
Nov 26, 2007
3
0
1
Feb 26, 2008
#8
  • Feb 26, 2008
  • #8
There is no ridge really... a little diff in the way the light reflects off of it... but my fingernail barely catches on it... it reads 4.000". So .005" isnt enough to worry about? Just get a new set of rings and pop them back in?
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Feb 26, 2008
#9
  • Feb 26, 2008
  • #9
SQUIDBILLIES FTMFW!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 

Fast63

New Member
Sep 20, 2007
717
0
0
Feb 26, 2008
#10
  • Feb 26, 2008
  • #10
32ratrod said:
There is no ridge really... a little diff in the way the light reflects off of it... but my fingernail barely catches on it... it reads 4.000". So .005" isnt enough to worry about? Just get a new set of rings and pop them back in?
Click to expand...

well, you have to remember that the bore tapers out when going down. In other words, the bore is supposed to be larger closer to the crank, and the measurement is taken where the deck surface is. Your .005 difference is probably mostly in the fact that it is tapered. Give it a good hone and slap in some new rings I say.
 
You must log in or register to reply here.

Similar threads

A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
593
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
M
  • Poll Poll
Stroking a Mexico 289 or newer roller 302
  • MaryJaneTheMustang
  • Aug 12, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
162
1965 - 1973 Classic Mustangs -General/Talk- Aug 12, 2026
Bullitt347
W
I need a 1997 Mustang PATS A expert!
  • Wolfdogg
  • Oct 2, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
203
1996 - 2004 SN95 Mustang -General/Talk- Oct 5, 2026
Noobz347
D
Fuel 1985 GT Fuel Line Diagram
  • DienstXIV
  • Apr 17, 2025
  • Fox 5.0 Mustang Tech
Replies
8
Views
2K
Fox 5.0 Mustang Tech Jul 12, 2025
DienstXIV
D
N
Power door lock motor Question
  • NYFox
  • Mar 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
414
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 17, 2026
NYFox
N
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?