302......306.....331 ????

So what do you guys think, just find a used block or buy a new one. I have checked ebay and other websites and found some pretty decent deals, if i go used im just scared of running into a cracked block. If i go 331, should i just buy a sportsman block, the sportsman block i found says that it comes finished 4.00 bore, so that means i would need to get it bored out right? All1knew, you said you built a 306 on a budget, about how much hp would a 306 make with good heads and a supercharger? What pistons, etc do you suggest i look at? How much money would you say i will save doing a 306 over a 331? I need as much help on this as possible because this will be my first engine build. So im sorta leaning on the 306 route but at the same time I see that more people prefer doing a 331. Right now, I really need help figuring out how to start my engine project. Does anyone know of any good deals on engine blocks or shortblocks? And keep sending me your opinions and information. THANKS!!
 
If you buy a new Sportsman block at 4.00" bore and throw your stroker 3.25" crank in it, you have a 327 cubic inch motor instead of a 332. The only reason you see so many 332's is because people start with a used block that needs a .030" overbore to clean it up.

If you build a supercharged 306, you can add boost to a HP level that will put the stock block in jeopardy -- the stock block itself is the weak link.

How are you gonna use the car? What power level do you want to build to? The answer to those questions should dictate how you build the motor. If you're serious about boost and HP, I'd start with the updated block. No sense taking a chance with power levels that could break a stock block which usually destroys and/or damages a lot of other engine parts at the same time.
 
If you buy a new Sportsman block at 4.00" bore and throw your stroker 3.25" crank in it, you have a 327 cubic inch motor instead of a 332. The only reason you see so many 332's is because people start with a used block that needs a .030" overbore to clean it up.

If you build a supercharged 306, you can add boost to a HP level that will put the stock block in jeopardy -- the stock block itself is the weak link.

How are you gonna use the car? What power level do you want to build to? The answer to those questions should dictate how you build the motor. If you're serious about boost and HP, I'd start with the updated block. No sense taking a chance with power levels that could break a stock block which usually destroys and/or damages a lot of other engine parts at the same time.
 
Mike it is actually a 331.515 :D :p

I agree with Mike, really depends on your intentions and future modification of the car. The Sportsman block is rated for 450hp, some have been pushed past but they are not made for high HP.

A good 306 is only a few hundred dollars cheaper then a 331 in the long run, if you have to buy internals I feel you should not give up the additional cubic inches.
 
Michael Yount said:
Exactly Rick - which must be rounded up to 332. Why? Well, do the math on the 5.0L; if you round down to 331, then we also have to start calling our venerable 302 a "301". Can't have that can we?

hehe...very true
 
I have a stock block, FMS 42 lbs. injectors, 94-95 Fuel Rails, 255 Walbro Pump, Vortech T-Rex, Vortech S-Trim with 3.12 inch Pulley, Edelbrock RPM II Intake, Ford Anderson Motorsport Power Pipe, Edelbrock RPM Heads, 75 Throttle Body, 77 Pro-M Mass Air Meter, Vortech Mini-Race Bypass Valve, Canto Main Support with ARP Bolts, Canton 7 Qt. Oil Pan. the car was dynoed at Mustang Magic in Deer Park, L.I. August 2005 and the car went 492 horses with 14lbs. of boost at 5800 RPM's. I was happy with the numbers, but I definitely want to go with a 306 or 331 block with some forged internals and call it a day. For a street car that I drive mostly in the summer I am happy to beat the the hell out of these Civic wanna be race cars.