• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

8.8 ring & pinion from explorer

  • Thread starter Thread starter joe3
  • Start date Start date Jan 27, 2006
J

joe3

New Member
Dec 30, 2005
23
0
0
Jan 27, 2006
#1
  • Jan 27, 2006
  • #1
when you get used do you have to reshim pinion if using old bearing
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jan 27, 2006
#2
  • Jan 27, 2006
  • #2
when installing gears you should always replace all shims,bearings, races,crush sleeve and seals with good namebrand parts.my best advice. i have know people who have reused bearings,shims and even crush sleeves needless to say they have wining problems with there rear end gears.and i would also recommend rebuilding the traction lok.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jan 27, 2006
#3
  • Jan 27, 2006
  • #3
oh ya my 3.73 gears i installed came out of a ford explorer. and they work great..
 
J

joe3

New Member
Dec 30, 2005
23
0
0
Jan 27, 2006
#4
  • Jan 27, 2006
  • #4
what i ment to say was will the pinion depth still be the same sence they are both 8.8 from ford asilimbly
 

TheBocSez

New Member
Feb 3, 2004
652
0
0
Converse, TX
Jan 27, 2006
#5
  • Jan 27, 2006
  • #5
Im ghetto, but I got a set of 4.10's from an explorer and installed them using the old crush sleeve and shim and have no problems or whine. I may have been lucky and the proper thing to do would be replace everything but the question was could it be done and it can cause I did it.
 
J

joe3

New Member
Dec 30, 2005
23
0
0
Jan 27, 2006
#6
  • Jan 27, 2006
  • #6
thanks for the imput i thought it could because they were both set up by ford
 

LilRedPony

New Member
May 12, 2003
31
0
0
Arizona
Jan 27, 2006
#7
  • Jan 27, 2006
  • #7
You should check the pinion depth if switching gears, if your pinion is off it will change the wear pattern and could really screw things up. The shim hight will probably be the same, mine was with new ford 3.55's, but just to be on the safe side I would check. Get a intallation kit, it should come with new seals, crush sleeve, pinion nut, shims, ect. well worth it imo. I would also do the trak-lok if it needs it and the axle bearings/seals. Also you will need to set the backlash and check the wear pattern.
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Jan 28, 2006
#8
  • Jan 28, 2006
  • #8
I had one shop do my 5.0 with all new everything, bearings, seals, shims, crush sleeve and cups. It's whiney and now the T/L needs to be rebuilt since they said it didn't at the time despite the fact that the rebuild kit was right there.

I had a guy in his backyard garage replace my gears in my '95 5.0 F-150. He also removed the open diff and replaced it with a T/L from a Explorer. He did adjust the shims but he reused the old crush sleeve and rebuilt the T/L (with the rebuild kit that I had leftover from the 5.0 fiasco) and I couldn't be happier.

No whine and when you push on the truck from the side you can't hear the C clips clunking around. My 5.0 has a definate clunk when you push on it from the side.
 
You must log in or register to reply here.

Similar threads

Engine Are These rings OK?
  • PonyGTrider
  • Sep 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
343
Fox 5.0 Mustang Tech Sep 26, 2026
PonyGTrider
O
8.8 Pinion Nut Leak
  • OX1
  • Jan 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 5, 2026
OX1
O
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
726
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
17
Views
1K
SN95 V6 Mustang Tech Aug 29, 2026
joeybuddy96
J
S
Drivetrain 8.8 Pinion and 302 rear main seal leaks after replacing. 93 5.0 with t-5
  • Steigy4827
  • Jun 23, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
888
Fox 5.0 Mustang Tech Apr 1, 2026
Steigy4827
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?