• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

95 Cobra - Barn Find - Issues - Help

  • Thread starter Thread starter Rocky Williamson
  • Start date Start date Aug 29, 2017
R

Rocky Williamson

New Member
Aug 29, 2017
1
0
1
Aug 29, 2017
#1
  • Aug 29, 2017
  • #1
Ok guys. I need some help. I found a 1995 cobra in a guys back yard. I've been playing with it for a few weeks. I have a miss/studder when it idles and when it gos down the road. I have done a tune up.
NEW parts.
Plugs wires
Pick up coil
Cap button
Coil
I have not found any vac leaks. But this studder is getting on my nurves. I am a mechanic. I fix people's cars all the time and I can't get this miss out of my own. This is my play toy and it's on a budget. I can think of plenty to change. But has anyone else had this issue.
 

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor
Admin Dude
Jan 4, 1985
43,563
21,730
234
Box behind Walmart
Aug 29, 2017
#2
  • Aug 29, 2017
  • #2
How long did it sit?
Did you disconnect the fuel rails and pump out the old gas?
Does the fuel pump prime when you switch the ignition to 'ON'?
Have you pulled codes?
 

95BlueStallion

My assy trans to myself
15 Year Member
Feb 22, 2007
5,130
3,103
214
Cedar Rapids, Iowa
Aug 29, 2017
#3
  • Aug 29, 2017
  • #3
Dumb question, but did you change the plugs also, and clean the MAF sensor?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 29, 2017
#4
  • Aug 29, 2017
  • #4
How do we know that this isn't someone else's car and you are using our tech support to make a buck?

I am glad to help out my fellow auto enthusiast and have done so many times.
However I am seriously opposed to helping someone who is supposedly a professional mechanic trying make a buck out of some poor guy's misfortune.

Think I am just some old windbag blowing off hot air? Google jrichker and see what you get

Barn car find checklist: first steps to get it back on the road.

First of all, carefully check the underhood area to make sure that rodents haven’t had a feast on the electrical wiring, air ducts and vacuum lines. Replace and repair any visible damage. Replace the battery if you haven’t already done so.

Next, drain ALL the engine fluids, transmission fluid, pump the fuel tank and fuel lines clear.

Get several cans of brake fluid, you will need it to flush the brakes. Loosen all 4 brake bleeders one at a time and flush the brake system by pumping the brake pedal. You will need to bleed the brakes when you finish flushing them. Brake fluid absorbs moisture if it sits for a long time and corrosive compounds start to brew themselves in the brake system.

Pumping out the old gas - do this before replacing the fuel filter if possible;
If the old pump still works, you can use it to pump the tank out.
1.) Separate the pressure line (the one with the Schrader valve on it) using the fuel line tools.
Look in the A/C repair section for the fuel line tools. They look like little plastic top hats. You will need the 1/2" & 5/8" ones. The hat shaped section goes on facing the large part of the coupling. Then you press hard on the brim until it forces the sleeve into the coupling and releases the spring. You may need someone to pull on the line while you press on the coupling.



OR



View: https://www.youtube.com/watch?v=vRTjYAxvaCs


Use a piece of garden hose to run from the pressure line to your bucket or gas can. Make sure it is as leak proof as you can make it. Fire and explosion are not part of the repair process...

2.) Jumper the fuel pump’s test point to ground.



Turn the ignition switch to the Run position. the fuel pump will pump the tank almost dry unless the battery runs down first.

Some 5 gallon paint pails lined with garbage bags are good to hold the gas. The garbage bags provide a clean liner for the pails and keep the loose trash out of the gas. If you decide to use a siphon, a piece of 1/2" garden hose stuck down the filler neck will siphon all but a gallon or so of the gas.

The fuel filter is on the passenger side of the car on the body just over the rear axle housing. Pull the plastic clips out by grasping the tabs with a pair of needle nose pliers or a screwdriver.

]View: https://www.youtube.com/watch?v=i-JU54w7FL4]

At this point you have fresh engine fluids, fresh gasoline, new filters, new battery fresh brake fluid, and have replaced or repaired any rodent damage.
Then change ALL the filters (fuel, air & oil). Then put in new oil, new antifreeze, and 5 gallons or so of new gasoline. Be sure to replace the all the fan belt or belts. Reusing old belts are an invitation to break and leave you stranded or overheated.

Pull the spark plugs out and squirt some oil down inside the cylinders to lube them up. While the spark plugs are out, examine them for signs of damage or fouling. Write down which plug came from which cylinder and write down any negative things that you saw when you examined the spark plugs.

This next step is for those who have successfully removed and reinstalled a 5.0 Mustang distributor. Pre-oil the engine to insure that everything is lubed up good before the engine starts. Turn the engine up to where the distributor rotor points to #1 cylinder. Mark the distributor base with a scratch mark or something else that isn’t going to get rubbed off. Then remove the distributor and stick a ¼” socket on a12” extension on an electric drill. Place this rig on the oil pump shaft in the hole below the distributor. Turn the ignition switch to Run but don’t crank the engine. Run the drill counterclockwise while your assistant watches the oil pressure gauge.

For the less experienced DIY’er, here is a less complicated procedure.
While the spark plugs are out, crank the engine until you see the oil pressure gauge indicate pressure. If you don’t see any indication of oil pressure at the gauge after 30 seconds or so of cranking, you have some other problems. This is the time to stop and investigate them.

Put the old spark plugs back in if they look good; replace the ones that don’t. Have a spare set of new spark plugs handy for installation once you get the engine running. Why? The oil you squirted in the cylinders will lube things up, but it may also foul the spark plugs. Don’t foul the new plugs by putting them in cylinders that may oil foul the plugs.

Remove the distributor cap, and examine it and the rotor for signs of moisture and tracks. Lightly spray the inside of the distributor cap with WD40 to displace any moisture, and then wipe it up with a clean paper towel. Replace any cap or rotor that shows signs of damage, excessive corrosion or tracking that won’t wipe up with a shot of WD40.

Put the distributor cap back on, secure any loose wiring, vacuum lines, check the fluid levels, check belt tension and tighten any fasteners that you may have loosened. You are now ready to see if the engine will run.
 
Last edited: Aug 29, 2017
Reactions: Flatfoot, General karthief and 95BlueStallion

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor
Admin Dude
Jan 4, 1985
43,563
21,730
234
Box behind Walmart
Aug 29, 2017
#5
  • Aug 29, 2017
  • #5
jrichker said:
Think I am just some old windbag blowing off hot air? Google jrichker and see what you get
Click to expand...

Interwebz Herpies?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 30, 2017
#6
  • Aug 30, 2017
  • #6
Noobz347 said:
Interwebz Herpies?
Click to expand...
Many sleepless nights and exhaustion if you were to chase all the links...
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,131
10,748
213
polk county florida
Aug 30, 2017
#7
  • Aug 30, 2017
  • #7
Or when you go to sleep you'll have nightmares of joe chasing you around hitting you with a repair manual shouting YOU DID IT WRONG!
Ask me how I know.
 
Reactions: jrichker
You must log in or register to reply here.

Similar threads

W
Speedometer and shifting issues
  • wyatt-tetro891
  • Aug 17, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
319
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 18, 2026
wyatt-tetro891
W
T
Fox Convertible top issues
  • TDM389
  • Feb 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
476
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 15, 2026
General karthief
B
Front window issues
  • bruno
  • Nov 7, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
204
Fox 5.0 Mustang Tech Tuesday at 10:26 PM
AeroCoupe
A
Resolved Electrical Help Please
  • Alabama
  • Jan 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
378
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 22, 2026
AeroCoupe
C
98 gt fuel pressure issues
  • chasecollier1984
  • Jun 2, 2026
  • SN95 4.6L Mustang Tech
Replies
0
Views
187
SN95 4.6L Mustang Tech Jun 2, 2026
chasecollier1984
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?