• Mustang Forums
  • Special Production

Roush '98 Underhood decal questiion

  • Thread starter Thread starter digdoug
  • Start date Start date Jul 4, 2006
D

digdoug

Member
Jan 7, 2003
97
0
6
Jul 4, 2006
#1
  • Jul 4, 2006
  • #1
I was out detailing some on my car and I have a question. I have the two decals on my radiator support (one for the fan, one for the air bag sensor), but no decals on the bottom of my hood. I have the Saleen installed heat extractor hood. Should there be a decal installed on the underside like on the factory hoods? If so can someone tell me what all is supposed to be under there so I can buy the correct decals. Thanks!!
 

SVT Saleen

New Member
Aug 10, 2005
456
0
0
Jul 5, 2006
#2
  • Jul 5, 2006
  • #2
The hood should contain the federal emissions certification decal but apparently Saleen did not install them on all of their cars when replacing the OEM hood with the composite hood.

I, too, have the composite hood but I have absolutely ZERO decals on the underside or anywhere in the engine compartment. I kinda like the clean, no-decal look.

However, the lack of the emissions certification decal created a bit of a dilemma when I went to register the car. The CA DMV would not allow the car to be registered without confirming that it was certified for CA emissions even though it passed the emissions test. What was the qualification for being CA emissions certified?

The missing decal.
 
D

digdoug

Member
Jan 7, 2003
97
0
6
Jul 5, 2006
#3
  • Jul 5, 2006
  • #3
OK, well as long as it was left off by Saleen I don't mind it being missing. I like it better without too, but wanted it to be correct. Thanks for the info!!!
 

SVT Saleen

New Member
Aug 10, 2005
456
0
0
Jul 6, 2006
#4
  • Jul 6, 2006
  • #4
If you want or need the emissions certification decal, any Ford dealer can order it for you. They'll just need your VIN to order the specific decal for your vehicle.

I had one ordered for mine but it arrived after I had already successfully registered the car so now it is stored along with all my other documentation (just in case I might need it in the future).
 
You must log in or register to reply here.

Similar threads

J
SN95 Hello new to this app
  • James S
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
108
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
Habu135
Engine Radiator with no shroud provision... What to do?
  • FastDriver
  • Apr 22, 2026
  • Fox 5.0 Mustang Tech
Replies
16
Views
318
Fox 5.0 Mustang Tech Apr 25, 2026
FastDriver
C
98 gt fuel pressure issues
  • chasecollier1984
  • Jun 2, 2026
  • SN95 4.6L Mustang Tech
Replies
0
Views
61
SN95 4.6L Mustang Tech Jun 2, 2026
chasecollier1984
C
T
Fox Help Request: Clutch Cable Installation on T5 Swap — I Can’t Find the Mounting Hole
  • TDM389
  • Feb 19, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
156
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 19, 2026
nickyb
Engine Themostat
  • Mindseye007
  • Jan 30, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
701
Fox 5.0 Mustang Tech Feb 1, 2026
86HO5.0
8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • Special Production
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?