• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

? about which timing cover gasket?

  • Thread starter Thread starter jaymac
  • Start date Start date Jan 4, 2006

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Jan 4, 2006
#1
  • Jan 4, 2006
  • #1
Autozone has 2 choices: Felpro w/o Sleeve "N" seal.
Or Felpro w/ Sleeve "N" seal.
What's the difference?
Also, do I have to buy a whole oil pan gasket to get that one piece for the front of the pan??
Thanks....
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 4, 2006
#2
  • Jan 4, 2006
  • #2
Unless your crank is damaged you do not need the sleeve and seal, it comes with the snubby pieces to replace the oil pan front section.
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Jan 4, 2006
#3
  • Jan 4, 2006
  • #3
Probably stupid question, but, are you talking about noticeable obvious-while-you're-driving-it "damaged", or when I take the cover off, might I notice something that requires the sleeve and seal??
Thanks Rick
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 4, 2006
#4
  • Jan 4, 2006
  • #4
If it has a groove you need the sleeve, personally I've never used one.....

Just make sure it has the timing cover gasket, oil pan pieces, front oil seal, the water pump gasket, and thermo gasket...

I usually buy a Fel-Pro 2718 kit, known as a R.A.C.E kit. It has ll the above, plus a rear main seal, and some other small gaskets for just a few bucks more, much cheaper then if you bought them seperate.
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Jan 4, 2006
#5
  • Jan 4, 2006
  • #5
Hey just seen this thread and i'm doing a engine build up where are you guys getting this new gaskets? I need every thing for the top end. Thanks
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 4, 2006
#6
  • Jan 4, 2006
  • #6
I get mine from my local parts store whom I have a commerical account with, Summit and Jegs also carry them.
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Jan 4, 2006
#7
  • Jan 4, 2006
  • #7
do I need to remove the thermostat??
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Jan 4, 2006
#8
  • Jan 4, 2006
  • #8
You can probably get away without taking the Thermostat housing off. I swapped gaskets last winter and used the opportunity to install a new thermostat.
 

mustangsally93

New Member
Sep 26, 2005
281
0
0
Omaha,NE
Jan 4, 2006
#9
  • Jan 4, 2006
  • #9
Just wanted to say thanks for the help..
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Jan 4, 2006
#10
  • Jan 4, 2006
  • #10
yeah, my T-stat and gasket are both brand-new...
 

jaymac

New Member
Feb 18, 2004
995
0
0
Northern Mass
Jan 4, 2006
#11
  • Jan 4, 2006
  • #11
well, I picked up the Gasket set: timing cover, water pump(s), front seal, rubber seal for bottom of cover, 2 cork pieces, and mech fuel pump which I don't need...
Got new oil and the permatex red spray. Gotta make sure I have enough RTV, and an oil filter, new anti-freeze, and I should be good to go, right???
 
You must log in or register to reply here.

Similar threads

A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
724
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
394
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
17
Views
1K
SN95 V6 Mustang Tech Aug 29, 2026
joeybuddy96
J
J
'04 3.8L V6 mineral deposits and oil on #3 cylinder. Does it need a rebuild or something simpler?
  • joeybuddy96
  • Mar 18, 2026
  • SN95 V6 Mustang Tech
Replies
15
Views
707
SN95 V6 Mustang Tech Sep 29, 2026
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?