• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Accufab

  • Thread starter Thread starter 04sonicblueGT
  • Start date Start date Jun 25, 2007

04sonicblueGT

New Member
Nov 20, 2004
80
0
0
Jun 25, 2007
#1
  • Jun 25, 2007
  • #1
I installed an accufab TB and plenum yesterday. I got the part from a friend that just got rid of his gt. got everything installed and good but there is a spacer that is between the tb and plenum because of this spacer my cable for my cruise control is to short and will not reach. my throttle cable reached fine it just took the slack out of my peddle. is there an extension for my cruise control avaible. i have search forums and have been unable to find anything on this. Or would i be better off taking the spacer off ?

Also it is safe to run predators performance tune with these part ( also have aftermarket mid pipe and cat back on the car), i will be getting it tuned just wnat to know if it is safe to run until i can get it tuned on the dyno?

Thanks
 

four six

Member
Jan 19, 2006
506
2
18
Hobart, IN
Jun 25, 2007
#2
  • Jun 25, 2007
  • #2
Your canned tune should be fine till you go get it tuned.
 

goshia

New Member
Jul 1, 2005
252
0
0
Mead, Colorado
Jun 25, 2007
#3
  • Jun 25, 2007
  • #3
Pull the spacer out. That is I am assuming it is one of those 1/2 inch alluminum spacers that acvertise 10-15HP gain "BS". It you want to leave the spacer in your going to have to grind down the cruise control plastic donut and feed it thur its holder and find away to mount it again. I would suggest just remove the spacer. Your ok to run with the predator tune that is currently on the car.
 

04sonicblueGT

New Member
Nov 20, 2004
80
0
0
Jun 25, 2007
#4
  • Jun 25, 2007
  • #4
well that answers that. thanks guys. The spacer was on it when i got so i figured i would leave it on but its 4 bolts so its gone.

Thanks again
 
You must log in or register to reply here.

Similar threads

J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
284
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
J
Low RPM jerking
  • Justinkins
  • Jul 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
226
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 11, 2026
fasterthangas
F
For Sale 2006 Mustang GT Steering Wheel with Cruise Controls
  • lenko
  • Sep 3, 2026
  • Other Classifieds
Replies
0
Views
129
Other Classifieds Sep 3, 2026
lenko
3
Hammer shifter problems
  • 387lx
  • Apr 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
254
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 11, 2026
General karthief
D
Running both lean and rich with O2 heat codes
  • Danceswithfire5
  • Aug 30, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
170
SN95 V6 Mustang Tech Sep 5, 2026
apple99Mustangdude
A
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?