• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Air bag light question

  • Thread starter Thread starter 88306stang
  • Start date Start date Mar 8, 2007

88306stang

New Member
Jun 20, 2004
87
0
0
Mar 8, 2007
#1
  • Mar 8, 2007
  • #1
The air bag light is blinking in my 93 Mustang GT it will blink once then pause and blink 3 more times then does it all over again. Does any body know what this code means?
 

88306stang

New Member
Jun 20, 2004
87
0
0
Mar 8, 2007
#2
  • Mar 8, 2007
  • #2
Anybody
 

rickd93_lx

New Member
Dec 22, 2005
162
0
0
Mar 8, 2007
#3
  • Mar 8, 2007
  • #3
has your air bag been deployed ussaully it will blink if the bag has beeen deployed or the sensor has gone bad. replacing a deployed air bag an ghanging the sensor will stop the light. if the air bag is not a concern you can unplug the air bnag module (the baby blue box behind the radio) just unplug the harnesses attached to it and it will stop if you remove the light from the dash the blinking will be replaced with an annoying beep.
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Mar 8, 2007
#4
  • Mar 8, 2007
  • #4
Not sure about the code, but it usually means that the system has found a problem, or thinks there is a problem. If the light is on, the system may be shut off.

On my 97 F150, pulling the air bag fuse with the battery connected will set the light and shut the system off. As far as I know, only a dealer can reset the light. It was $54 at the dealer. Took a hour on Alldata to figure out the problem.

VERY ANNOYING!!!

You may just want to bite bullet and go to the dealer. Autozone or someone else hear should have the codes.
 

Shakerhood

20+ Year Stangneter
Oct 28, 2004
3,361
211
114
Ohio
Mar 9, 2007
#5
  • Mar 9, 2007
  • #5
Code 13 is Front Crash Sensor or Air Bag Circuit Shorted to Ground.
 

88306stang

New Member
Jun 20, 2004
87
0
0
Mar 9, 2007
#6
  • Mar 9, 2007
  • #6
Thanks guys ill have to see if i can get it taken care of today.
 
I

iwashmycar

20+ Year Stangneter
Apr 7, 2004
1,236
1
39
Columbus, Ohio
Mar 9, 2007
#7
  • Mar 9, 2007
  • #7
mine had a grounding problem too. I tried tightening all the sensor bolts to no avail, and then it fixed when I put some electrical tape over the bolt heads. I guess it is grounding out on the hood prop rod. I may just need some better grounding bolts. Theyre getting corroded
 
You must log in or register to reply here.

Similar threads

S
ECU/PCM ISSUE
  • Santi1015
  • Jun 29, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
275
SN95 4.6L Mustang Tech Jun 29, 2026
Santi1015
S
W
I need a 1997 Mustang PATS A expert!
  • Wolfdogg
  • Oct 2, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
207
1996 - 2004 SN95 Mustang -General/Talk- Oct 5, 2026
Noobz347
I
Engine Help requested in identifying how to resolve engine light issue
  • Ianslaney
  • Oct 4, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
187
SN95 4.6L Mustang Tech Oct 4, 2026
Bullitt347
C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
255
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
B
Help! Fox with idle issues
  • bbarton
  • Sep 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
322
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 12, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?