• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

air conditioner

  • Thread starter Thread starter Beasty306GT
  • Start date Start date Aug 4, 2007

Beasty306GT

Active Member
Dec 19, 2002
671
4
28
Oxford,Mass
Aug 4, 2007
#1
  • Aug 4, 2007
  • #1
Hey everyone i had my a/c charged today...and it was ice cold...i went to use it a lil while ago and it was blowing warm air.....the a/c clutch wasnt spinning...is there any ideas out there to make tha thing move......this is all new to me so please help me out..im pissed it was freezing cold and now......well.......i dunno please help if possible thanxs
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 4, 2007
#2
  • Aug 4, 2007
  • #2
Most of the gas has probably leaked out. There is a low pressure cutoff switch mounted on top of the accumulator (aluminum canister on the firewall). It job is to shut off the compressor when the refrigerant charge gets too low. This protects the compressor from lack of lubrication, since the refrigerant carries the oil used to lubricate the compressor.

The two wires inside the low pressure cutout switch wiring connector can be jumpered together to test the system. That bypasses the switch and turns on the compressor when the refrigerant level is low. Don't run the system for more than 30 seconds, because low refrigerant also means low oil. Lack of oil will quickly damage the compressor .
 

Beasty306GT

Active Member
Dec 19, 2002
671
4
28
Oxford,Mass
Aug 4, 2007
#3
  • Aug 4, 2007
  • #3
is there a kit where i can test the pressure in the line? i just had a body shop charge it....blew perfectly cold air.....few hrs later went to turn it on and it was warm air again....are they any repair kits if it is leaking....
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Aug 4, 2007
#4
  • Aug 4, 2007
  • #4
subscribing
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 4, 2007
#5
  • Aug 4, 2007
  • #5
SickSix said:
is there a kit where i can test the pressure in the line? i just had a body shop charge it....blew perfectly cold air.....few hrs later went to turn it on and it was warm air again....are they any repair kits if it is leaking....
Click to expand...

Since you are not familiar with how A/C works, here some background theory:

The condenser is up front of the radiator, and it is supposed to condense the hot gas from the compressor into a hot liquid. The hot liquid goes to the expansion valve located in the tubing next to the firewall. The expansion valve lets the hot liquid expand and become a cold gas, the cold gas goes to the evaporator inside the car where the fan blows on the evaporator exterior. The heat transfer from the air inside the car to the cold gas inside the evaporator causes the A/C to blow cold air. The now cool gas goes to the compressor where it gets compressed again into a hot gas and the process starts all over again. Keep in mind that this is a closed system, and the gas inside the A/C doesn't get out unless there is a leak, which is where you are at.

Here's where the problem gets sticky. All the original fox body Mustangs were made to use R12 refrigerant. R12 is no longer available unless you have an EPA 609 license. That means the system needs to be converted to use R134. Putting R134 on top of R12 without doing a proper conversion will cause compressor failure and metal from the compressor will circulate throughout the system. When this happens, it requires an extensive and expensive flush of the A/C system to get all the metal and other contaminants out. Skip doing the flush and clean thing and the new compressor will quickly fail.

When a R134 conversion is done, the installer is supposed to replace the service fittings with R134 style quick connector couplings.

Typical low pressure side R134 coupling


Typical high pressure side R134 coupling


Then he places a R134 conversion sticker on the car. The typical sticker looks like this, yours may be different.




They are also supposed to replace all the O rings with R134 compatible O rings. The R134 gas molecule is smaller than the R12 molecule, so R12 O rings will be prone to leakage.

See http://bellsouthpwp.net/l/r/lrichker/Mustang_tech/R134a_conversion/r134a_conversion.htm for R134a Conversion & recharge help

If the gas leaks out, usually it is because one of the O ring seals is bad. High quality R134 conversion is supposed to include new green O rings for all the joints and couplings. When you open the system to replace the O rings, all of the refrigerant must be removed and recovered and the system vacuumed down prior to recharging.

R134 recharge kits with refrigerant/leak detector dye can are available at most auto parts stores. Some of the R134 refrigerant refills have a leak stop in them. BUT beware! The stop leak can block the expansion valve, causing system failure. The refrigerant/dye recharge kits are popular because the green dye makes a very visible indicator where the leaks is. Some of the recharge kits include a pressure gauge so you have some idea of how much refrigerant is in the system while it is running.
 

the pony boy

Founding Member
Apr 19, 2002
358
0
16
10512
Aug 5, 2007
#6
  • Aug 5, 2007
  • #6
what if you check the pressure and its good whats the procedure than? phil (low pressure sensor is good )
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,374
18,121
224
Massachusetts
Aug 5, 2007
#7
  • Aug 5, 2007
  • #7
You need to replace all the o-rings with green o-rings specific to the r-134a. After replaing the rings, then the shop should have pulled a vacuum first on the system for a specific amount of time, then added the proper amount of oil and refridgerant.

Even that's not a complete r-134a conversion.


If all they did was hook up a couple cans and charge the system, you got screwed.
 

Beasty306GT

Active Member
Dec 19, 2002
671
4
28
Oxford,Mass
Aug 5, 2007
#8
  • Aug 5, 2007
  • #8
where the best place to have it checked out??? garage or an a/c shop????
 

mustangjoe87

Member
Jul 23, 2004
364
0
16
Harrison Twp., Michigan
Aug 5, 2007
#9
  • Aug 5, 2007
  • #9
They probably didnt check for leaks or replace any o rings and just charged it. Take it back and tell them to do it right.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,374
18,121
224
Massachusetts
Aug 5, 2007
#10
  • Aug 5, 2007
  • #10
SickSix said:
where the best place to have it checked out??? garage or an a/c shop????
Click to expand...


A/C shop will do it right....i hope.

Garages tend to just plug in a couple cans and charge you $75. BTW, those cans they put in cost about $6 each at autozone. So it's $18 in freon and about $50ish for them to hook the hose up.
 
You must log in or register to reply here.

Similar threads

B
A/C Issues
  • Boats90GT
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
213
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
Mcmahst
E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
3
Views
370
2005 - 2009 Specific Tech Sep 26, 2026
manicmechanic007
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
M
Progress Thread mkk50's Progress Thread
  • mkk50
  • Aug 4, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
19
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 22, 2025
Noobz347
A
95 Gt intermittent backfire
  • A_A_Ron
  • May 26, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
507
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 26, 2025
A_A_Ron
A
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?