• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

AIRB & AIRD Help

  • Thread starter Thread starter Treachery
  • Start date Start date Jun 8, 2007
T

Treachery

Founding Member
Jun 9, 2002
148
0
17
Jun 8, 2007
#1
  • Jun 8, 2007
  • #1
I removed the AIRB & AIRD valves in my '93 Mustang GT so i could tighten up the header bolts. However, being the genius that i am, i forgot to note how these valves were positioned.

Attached is a pic of how i have these valves connected.

Is this correct?

Thanks.
 

Attachments

  • airb&aird.webp
    20 KB · Views: 399

cjones

Founding Member
Jul 20, 2002
1,561
0
37
Avondale, AZ
Jun 8, 2007
#2
  • Jun 8, 2007
  • #2
that appears to be correct.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 8, 2007
#3
  • Jun 8, 2007
  • #3
Some review of how it works...

The Thermactor air pump (smog pump) supplies air to the heads or catalytic converters. This air helps burn the excess HC (hydrocarbons) and CO (carbon monoxide). The air supplied to the catalytic converters helps create the catalytic reaction that changes the HC & CO into CO2 and water vapor. Catalytic converters on 5.0 Mustangs are designed to use the extra air provided by the smog pump. Without the extra air, the catalytic converters will clog and fail.

The Thermactor air pump (smog pump) puts air into the heads when the engine is cold and then into the catalytic converters when it is warm. The Thermactor control valves serve to direct the flow. The first valve, TAB (Thermactor Air Bypass) or AM1 valve) either dumps air to the atmosphere or passes it on to the second valve. The second valve, TAD (Thermactor Air Diverter valve or AM2 valve) directs it to the heads or the catalytic converters. The air serves to help consume any unburned hydrocarbons by supplying extra oxygen to the catalytic process. The computer tells the Thermactor Air System to open the dump valve at WOT (wide open throttle) minimizing engine drag. The dump valve reduces the parasitic drag caused by the smog pump to about 2-4 HP at WOT.






Computer operation & control for the Thermactor Air System
Automobile computers use current sink technology. They do not source power to any relay, solenoid or actuator like the IAC, fuel pump relay, or fuel injectors. Instead the computer provides a ground path for the positive battery voltage to get back to the battery negative terminal. That flow of power from positive to negative is what provides the energy to make the IAC, fuel pump relay, or fuel injectors work. No ground provided by the computer, then the actuators and relays don't operate.

One side of the any relay/actuator/solenoid in the engine compartment will be connected to a red wire that has 12-14 volts anytime the ignition switch is in the run position. The other side will have 12-14 volts when the relay/actuator/solenoid isn't turned on. Once the computer turns on the clamp side, the voltage on the computer side of the wire will drop down to 1 volt or less.

In order to test the TAD/TAB solenoids, you need to ground the white/red wire on the TAB solenoid or the light green/black wire on the TAD solenoid.

To test the computer, you can use a test light across the TAB or TAD wiring connectors and dump the codes. When you dump the codes, the computer does a self test that toggles every relay/actuator/solenoid on and off. When this happens, the test light will flicker.
 
B

Biggeley

New Member
Mar 4, 2003
136
0
0
Jul 31, 2007
#4
  • Jul 31, 2007
  • #4
jrichker, this diagram is awesome.

Can you tell me though, am I correct in assuming that the vacuum source should be connected to the lower of the nipples on each solenoid? I've seen it shown both ways in various depictions. Was hoping that yours shows the "correct" orientation.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 31, 2007
#5
  • Jul 31, 2007
  • #5
Biggeley said:
jrichker, this diagram is awesome.

Can you tell me though, am I correct in assuming that the vacuum source should be connected to the lower of the nipples on each solenoid? I've seen it shown both ways in various depictions. Was hoping that yours shows the "correct" orientation.
Click to expand...

The vacuum line routing and connection is exactly the same as the original factory setup. The bottom of the vacuum control solenoids is connected to the vacuum source. The factory connectors make it very difficult to connect them upside down.
 
You must log in or register to reply here.

Similar threads

J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
341
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
220
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
Vacuum line question?
  • Mustang Momma
  • Feb 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
254
1996 - 2004 SN95 Mustang -General/Talk- Mar 3, 2026
Noobz347
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
402
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
O
Sooty/Oily Front Engine & Pulleys
  • ozenator
  • Jun 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
539
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 22, 2026
Blackhawkxx
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?