• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Aligning New Hatchback Properly

  • Thread starter Thread starter GoldenEagle91
  • Start date Start date Jul 20, 2014

GoldenEagle91

Active Member
Dec 25, 2012
240
16
29
Jul 20, 2014
#1
  • Jul 20, 2014
  • #1
Good evening guys,

This past Friday my Dad and I installed a newer hatch on my 79 Ghia and as we have it sitting now it is about half an inch off to the passenger side of the vehicle and there is about a half inch gap where water or squirrels would be able to get in. I am needing to know how to move it over to the driver side some so that I can get a good seal. I am really new to doing any body related work regarding alignment so any help is appreciated.

Thanks,
Andrew
 

flstang65

10 Year Member
Dec 6, 2007
1,484
135
94
SE Georgia
Jul 22, 2014
#2
  • Jul 22, 2014
  • #2
Pretty much trial and error. Put it on, check it, loosen it up, adjust, tighten it, check it again and repeat until you got it.
 

RacEoHolic330

I like to dress like a pretty girl
15 Year Member
Mar 4, 2003
4,014
1,698
203
Allentown, PA
Jul 23, 2014
#3
  • Jul 23, 2014
  • #3
I did the hatch on my 88 last week. Definitely a trial and error process. Mine was the same one I took off though. You may have other issues if yours came off a different vehicle.
 
Reactions: flstang65

mikestang63

SN Certified Technician
Aug 27, 2012
11,606
8,859
214
In the garage
Jul 23, 2014
#4
  • Jul 23, 2014
  • #4
The hinges could be tweaked. It's like fitting any other body panel, an art not a science.
 

madspeed

Colonel Mustard
Founding Member
Nov 29, 1999
8,913
1,332
204
a van down by the river
Jul 23, 2014
#5
  • Jul 23, 2014
  • #5
pain in the arse job right there
 

84Ttop

They make new pistons every day, so why worry?
5 Year Member
Jul 2, 2009
5,222
3,254
204
South Jersey
Jul 24, 2014
#6
  • Jul 24, 2014
  • #6
You will find most of your lateral adjustment comes from the two bolts that hold the hinges to the body and not the hinges to the hatch. You may have to remove the upper interior head liner trim to access these bolts. Hope this helps..... If all else fails, join the squirrels and grab a beer!
 
You must log in or register to reply here.

Similar threads

Still need an Alignment?
  • from6to8
  • Jun 1, 2025
  • 1994 - 1995 Specific Tech
Replies
3
Views
346
1994 - 1995 Specific Tech Jun 2, 2025
AeroCoupe
M
Inheriting (and likely restoration of) a 1965 Mustang
  • miniwheats235
  • Feb 17, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
2
Views
359
1965 - 1973 Classic Mustangs -General/Talk- Feb 19, 2026
Realmongo
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
468
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
360
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
470
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?