• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Any problems installing a Pypes o/r X?

  • Thread starter Thread starter fobra559
  • Start date Start date Dec 1, 2007
Prev
  • 1
  • 2
  • 3
  • 4
  • 5
First Prev 5 of 5

fobra559

At least it's more erect and not floppy anymore.
Nov 1, 2007
721
0
0
Lindsay, CA
Dec 16, 2007
#81
  • Dec 16, 2007
  • #81
georgio440 said:
I'm always on it now because I just want to hear it.

It seems to scare the ricers off, though.
Click to expand...

Yeah, I'm sure I'll be on it once I install it

Go to the car garages and set some alarms off now
 

georgio440

Member
Nov 22, 2007
195
0
17
Walnut Creek, CA
Dec 16, 2007
#82
  • Dec 16, 2007
  • #82
I already did last night when I went to see I Am Legend.
 

fobra559

At least it's more erect and not floppy anymore.
Nov 1, 2007
721
0
0
Lindsay, CA
Dec 16, 2007
#83
  • Dec 16, 2007
  • #83
How many did you set off? How was I am Legend? I so want to see that movie. Especially when he's deer hunting driving that Shelby
 

georgio440

Member
Nov 22, 2007
195
0
17
Walnut Creek, CA
Dec 16, 2007
#84
  • Dec 16, 2007
  • #84
Yeah the movie was pretty amazing. Go see it ASAP.

One thing though... Even after installing a new gasket, I still hear a slight leak from the passenger side. Do you think it's because the bolts aren't tight enough, or do I need some of the silicone crap to seal it up? I'm gonna get under the car tomorrow and see if I can tighten it up a bit more. It's hardly noticeable, though. Before I got a new gasket, it sounded like ****. Now it just sounds like air, rather than that annoying rattling sound that leaks produce.
 

fobra559

At least it's more erect and not floppy anymore.
Nov 1, 2007
721
0
0
Lindsay, CA
Dec 16, 2007
#85
  • Dec 16, 2007
  • #85
georgio440 said:
Yeah the movie was pretty amazing. Go see it ASAP.

One thing though... Even after installing a new gasket, I still hear a slight leak from the passenger side. Do you think it's because the bolts aren't tight enough, or do I need some of the silicone crap to seal it up? I'm gonna get under the car tomorrow and see if I can tighten it up a bit more. It's hardly noticeable, though. Before I got a new gasket, it sounded like ****. Now it just sounds like air, rather than that annoying rattling sound that leaks produce.
Click to expand...

I would think, tighten it up first and see and then seal it if it still leaks. If it doesn't work out, take it to a shop and have them look at it. They can probably fix it easily.
 

georgio440

Member
Nov 22, 2007
195
0
17
Walnut Creek, CA
Dec 17, 2007
#86
  • Dec 17, 2007
  • #86
I guess it's hard to properly tighten those bolts when you're using a 10" extension and a swivel head. :\
 

fobra559

At least it's more erect and not floppy anymore.
Nov 1, 2007
721
0
0
Lindsay, CA
Dec 17, 2007
#87
  • Dec 17, 2007
  • #87
georgio440 said:
I guess it's hard to properly tighten those bolts when you're using a 10" extension and a swivel head. :\
Click to expand...

You have any buddies that can help you out?
 

fast97gt

Active Member
Jan 2, 2007
1,082
2
49
north carolina
Dec 17, 2007
#88
  • Dec 17, 2007
  • #88
its the passenger i presume, i would loosen both the pass. and driver side, and tighten the pass side first, than the driver side . i had the same problem, cause the pass., side manifold is flat and the driver side has a ball flang. try that and see what happens. oh and i am legend was the sh** i thought.
 

fobra559

At least it's more erect and not floppy anymore.
Nov 1, 2007
721
0
0
Lindsay, CA
Dec 17, 2007
#89
  • Dec 17, 2007
  • #89
fast97gt said:
its the passenger i presume, i would loosen both the pass. and driver side, and tighten the pass side first, than the driver side . i had the same problem, cause the pass., side manifold is flat and the driver side has a ball flang. try that and see what happens. oh and i am legend was the sh** i thought.
Click to expand...

Dang, I have to see that movie. Everyone on here was like the Shelby scene was the s***, I might just pay to see that part and then after when it's done walk out
 

georgio440

Member
Nov 22, 2007
195
0
17
Walnut Creek, CA
Dec 17, 2007
#90
  • Dec 17, 2007
  • #90
fast97gt said:
its the passenger i presume, i would loosen both the pass. and driver side, and tighten the pass side first, than the driver side . i had the same problem, cause the pass., side manifold is flat and the driver side has a ball flang. try that and see what happens. oh and i am legend was the sh** i thought.
Click to expand...

Will that really work? I've been under that car so much in the past few days. The bolts are just in such an awkward place that I can't get in a good position to torque the bolts as hard as I potentially can.
 

lazerred02

New Member
Nov 19, 2004
190
1
0
FT Stewart, GA
Dec 18, 2007
#91
  • Dec 18, 2007
  • #91
fobra559 said:
Dang, I have to see that movie. Everyone on here was like the Shelby scene was the s***, I might just pay to see that part and then after when it's done walk out
Click to expand...

Here you go


http://movies.yahoo.com/movie/18097...wmv-s.52221307-,5453908-300-flash-s.52221341-
 

fobra559

At least it's more erect and not floppy anymore.
Nov 1, 2007
721
0
0
Lindsay, CA
Dec 18, 2007
#92
  • Dec 18, 2007
  • #92
lazerred02 said:
Here you go


http://movies.yahoo.com/movie/18097...wmv-s.52221307-,5453908-300-flash-s.52221341-
Click to expand...

Awesome! Thanks
 
Prev
  • 1
  • 2
  • 3
  • 4
  • 5
First Prev 5 of 5
You must log in or register to reply here.

Similar threads

L
Exhaust 95 gt pypes catted x pipe
  • Lx5.0fiend
  • Aug 22, 2025
  • 1994 - 1995 Specific Tech
Replies
5
Views
361
1994 - 1995 Specific Tech Sep 18, 2025
revhead347
Trick Flow Series R to Box R Upper Intake Road Block
  • Habu135
  • Mar 31, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3 4
Replies
78
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 6, 2026
Habu135
Sound deadener install
  • limp
  • Jun 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
203
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 17, 2026
limp
J
can you use the heads off a H O 302 to put on a regular 302 engine
  • Jan H
  • Feb 25, 2026
  • Other Auto Tech
Replies
6
Views
378
Other Auto Tech May 17, 2026
nickyb
Engine (EGR Deleted) Solution the hotter combustion chambers?
  • PonyGTrider
  • Jan 21, 2026
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
97
Views
3K
Fox 5.0 Mustang Tech May 2, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?