• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

auto shifter

  • Thread starter Thread starter jozan
  • Start date Start date Jul 19, 2006
J

jozan

New Member
Aug 26, 2005
60
0
0
Jul 19, 2006
#1
  • Jul 19, 2006
  • #1
im looking at a b&m console hammer will it let me hold it in second gear or do you have to have an aftermarket valve body
 
L

lang williams

New Member
Jun 11, 2003
567
0
0
cleveland, oh
Jul 19, 2006
#2
  • Jul 19, 2006
  • #2
i have the b & m hammer shifter in my car an the only difference between it and the stock shifter is the look (very cool) an the ratchet action (kinda pita if you drive it daily)...an the stops keep you from over shifting an going into reverse
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Jul 19, 2006
#3
  • Jul 19, 2006
  • #3
It wont hold 2nd gear. You need to change to something like the Lentech Street Terminator with the electronic lock out to be able to hold 2nd. But believe me, its well worth it!
 

ChromdOutDubs

Member
Sep 1, 2005
268
1
18
Tavares, Florida
Jul 19, 2006
#4
  • Jul 19, 2006
  • #4
This is something dont understand.... When i had my 4 banger in with its automatic trans, when you put the gear shifter in 2nd, on the floor ya know. I thought it would stay in 2nd gear until i pushed it to drive, or whatever. Am i missing something here, ( pretty sure I am ). I didnt drive the stang much when i got it, pretty much got it and ripped the entire thing down, for the new 408w and lots of other stuff.

-AJ
 
J

jozan

New Member
Aug 26, 2005
60
0
0
Jul 20, 2006
#5
  • Jul 20, 2006
  • #5
thats the point unless you hold it to the floor it goes into drive i dont like that
i want to be able to shift each gear without holding it to the floor thanks for your input guys
 

wythors

Get off my lawn!!!
Founding Member
May 17, 2000
2,277
35
69
C Addle
Jul 20, 2006
#6
  • Jul 20, 2006
  • #6
Try this:

Start out with the shifter in "1".
Run up as high as you want to.
When you're ready to shift into second, quickly slide the shifter into "D" then immediately back to "1". This needs to be done very rapidly.
The transmission will now hold second gear until you slide the shifter into "D".
 

eagleautosports

New Member
Jul 7, 2006
139
0
0
Mebane NC
Jul 20, 2006
#7
  • Jul 20, 2006
  • #7
I'd advise getting a manual valvebody. I got one earlier this year and love it. The old 1-D-1 shuffle wears out both the reverse band and the overdrive band because doing this way of shifting dumps the line pressure and cause the bands to apply prematurely. Anybody who can change a throttle body can put in a valvebody. It's messy but it'll outdo any shift kit you could get. Be a good time to get synthetic fluid in there too.
 

RYC CUKR

Founding Member
May 19, 2002
1,437
1
38
Orlando
Jul 20, 2006
#8
  • Jul 20, 2006
  • #8
wythors said:
Try this:

Start out with the shifter in "1".
Run up as high as you want to.
When you're ready to shift into second, quickly slide the shifter into "D" then immediately back to "1". This needs to be done very rapidly.
The transmission will now hold second gear until you slide the shifter into "D".
Click to expand...


Can you say no OD. The 1D1 shuffle is not good for an AOD. Eventually it you will burn up the OD band. Trust me, I know. Some people can go for quite a while doing the 1D1 and others after a few times the band is gone.

The best way is to get an aftermarket valvebody like a Lentech. Then you have 1-2-D and a switch for OD like the AODEs and 4RW70s.
 

$uperstang

New Member
Jul 20, 2004
476
1
0
Detroit, MI
Jul 20, 2006
#9
  • Jul 20, 2006
  • #9
I got a Transgo shift kit and 1-d-1 works like a charm with the shift kit. It does not put pressure on the bands like it used to without it. You can go from 1 to d and then wait a few hundred RPMS and shift it back down to 1 to hold 2nd.
 
You must log in or register to reply here.

Similar threads

J
Interior and Upholstery NEED HELP FINDING SHIFTER PLATE
  • Jschallitz
  • Nov 12, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
87
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 13, 2026
rednotch
3
B&m hammer shifter c4 question
  • 387lx
  • Mar 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
409
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 19, 2026
387lx
3
3
Hammer shifter problems
  • 387lx
  • Apr 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
269
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 11, 2026
General karthief
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
212
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
W
Speedometer and shifting issues
  • wyatt-tetro891
  • Aug 17, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
323
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 18, 2026
wyatt-tetro891
W
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?