• Mustang Forums
  • Special Production

Mach 1 auto vs. manual

  • Thread starter Thread starter ragu1585
  • Start date Start date Jun 28, 2005

ragu1585

Member
Jul 22, 2004
152
0
16
Spring, TX
Jun 28, 2005
#1
  • Jun 28, 2005
  • #1
I am hopefully picking up my mach tomorrow, and i couldn't help notice that its redline was 6k or so, and i know atleast the 5 speed is 7k, what gives?
 

Give Me TP

Member
Jun 17, 2004
936
0
16
Republic of Texas
Jun 28, 2005
#2
  • Jun 28, 2005
  • #2
Cast crank in autos vs forged crank in manuals.
 

ttown

Founding Member
May 30, 2002
815
0
0
Oklahoma
Jun 28, 2005
#3
  • Jun 28, 2005
  • #3
Well you need to buy a preditor or SCT tuner. The computer makes the auto shift like a sludge box. If I am shifting at 5700rpm I tend to hit the rev limiter on my car, it sputters and then shifts. If I shift from 4800 to 5200 rpms it won't shift until about red line at 6k. On my auto you may as well leave it in drive stock. It could be my car since I only have one but I'd say these cars are setup for more street driving. Tires and made to make a firm shift at will and there sweet.
 

ragu1585

Member
Jul 22, 2004
152
0
16
Spring, TX
Jun 29, 2005
#4
  • Jun 29, 2005
  • #4
well i just wanna confirm this, i did pick up my mach 1, 2004, 11,000 miles, auto, the dealer wanted 1500 down, 2250 for my 98 gt, and payments would of been over 600 a month, went to my credit union talked them down to 25k, put 1500 down on 5.35 interest, got to keep my 98 GT, financin 24,8xx, payments are around 470, first time buyer, with co signer, im 20, Boy do i love this car!
 
K

KeithCobraUH

Founding Member
Apr 19, 2002
192
0
16
Houston(Clear Lake)
Jul 12, 2005
#5
  • Jul 12, 2005
  • #5
Good job on going to the credit union, I don't trust dealership financing.


Get some mods with the money you saved!
 

BrutalStang

New Member
Aug 2, 2004
261
0
0
PA
Jul 12, 2005
#6
  • Jul 12, 2005
  • #6
your 20 with 2 mustangs? wow. nice cars by the way.

in my experience fords with autos shift higher when the over drive is turned off, just something to try.
 

ragu1585

Member
Jul 22, 2004
152
0
16
Spring, TX
Jul 18, 2005
#7
  • Jul 18, 2005
  • #7
so far on the mach, ive put the slp catback, and then added some tint and alarm and bumper inserts, and gt is being fixed right now and will hopefully be out the shop this week so i can finally sell it. 6k
 
K

KeithCobraUH

Founding Member
Apr 19, 2002
192
0
16
Houston(Clear Lake)
Jul 18, 2005
#8
  • Jul 18, 2005
  • #8
How do you like the SLP? Did you put it on?
 

ragu1585

Member
Jul 22, 2004
152
0
16
Spring, TX
Jul 18, 2005
#9
  • Jul 18, 2005
  • #9
i like the sound as much as i did my bassani, plus ALOT cheaper, and my tail pipes are stiff unlike on my driver side tailpipe on the GT! cant wait for the x pipe, got it dyno'ed today and the guys recommend the bassani x, but i want one with interchangable cats and straight pipe like slp's x, plus im hopin to find one that the cats, when on, dont hang as low as my gt so when i get a drop it dont drag everywhere! i took it to the local shop to have it put on, i have no tools, plus i had them tac it in place. all around a great product and no complaints so far!
 
K

KeithCobraUH

Founding Member
Apr 19, 2002
192
0
16
Houston(Clear Lake)
Jul 19, 2005
#10
  • Jul 19, 2005
  • #10
Did it dyno low? or did you expect more?
 

ragu1585

Member
Jul 22, 2004
152
0
16
Spring, TX
Jul 19, 2005
#11
  • Jul 19, 2005
  • #11
i was hoping around 265ish, but honestly i didn't know what to expect, it dynoed 258 and 271, they told me a nice air filter, x pipe and predator would get me close to 300ish, i raced an auto ws6 last night and my "258" put me about a car infront of it till i slowed due to a car in front of me! so i guess it aint too bad for now.
 
K

KeithCobraUH

Founding Member
Apr 19, 2002
192
0
16
Houston(Clear Lake)
Jul 19, 2005
#12
  • Jul 19, 2005
  • #12
The heat must have hurt you rnumbers.

Was that on a DynoJet or a Mustang dyno?

SAE or STD numbers?

SHould say on your dyno printout.

How many miles are on your car?
Do you have a K&N filter or the snorkel removed?
 

ragu1585

Member
Jul 22, 2004
152
0
16
Spring, TX
Jul 19, 2005
#13
  • Jul 19, 2005
  • #13
i hope it was the weather, this was about an hour laters temp, "89°F Felt Like 99°F Updated Jul 18 05:45 p.m. CT UV Index: 1 Low Wind: From SSE at 7 mph Humidity: 64% Pressure: 29.95 in. Dew Point: 75°F" it was on a dyno jet, not sure bout the std or sae cause i dont have the print out with me - but whats the diff between the 2? its got about 12,750 ish, and i removed the silencer but still have factory paper filter in. which k&n drop in can i go with? and can i get it at the auto zone?
 
You must log in or register to reply here.

Similar threads

J
2003 Mach 1 Wiring
  • JohnnyUtah
  • Mar 22, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
77
1996 - 2004 SN95 Mustang -General/Talk- Mar 23, 2026
squeak93
L
93 2.3L 5 speed manual with los of power
  • leadfoot67217
  • Jan 27, 2026
  • 2.3L (N/A & Turbo) Tech
Replies
0
Views
139
2.3L (N/A & Turbo) Tech Jan 27, 2026
leadfoot67217
L
Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
7
Views
123
1974 - 1978 Mustang II Talk & Tech Wednesday at 4:03 AM
extra_stout
Y
Speed density 302 to carb 351W
  • yaboity
  • May 29, 2026
  • Fox Engine Swaparoo
Replies
1
Views
44
Fox Engine Swaparoo May 29, 2026
AeroCoupe
C
strange noise coming from rear wheel
  • crazyone64
  • Oct 28, 2025
  • SN95 4.6L Mustang Tech
Replies
2
Views
191
SN95 4.6L Mustang Tech Nov 26, 2025
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • Special Production
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?