• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Bad Day, Car Won't Fire

  • Thread starter Thread starter brentwoodboy
  • Start date Start date May 18, 2005

brentwoodboy

New Member
Nov 25, 2002
472
0
0
Brentwood, TN
May 18, 2005
#1
  • May 18, 2005
  • #1
First of all, how do I reset the fuel pump cutoff switch? My dad jacked up the car and dropped it hard and it hasn't started since. I looked behind the tail light and the red button won't move (I tried to press it). Also, no spark is coming through from my coil... What could my problem be?
Oh and before this, Sunday I drove the car all day (afetr an intake manifold install) and it ran perfect. After that, I did the base idle reset thing from the website. The next morning, all it would do is strat up, sputter, and die. I tried revving but it would sputter up and down then die. On top of all this, we destroyed my bumper getting it up on a trailer. HELP ME!!!

Cliffs: Fuel pump may be off, no spark coming through, drove fine one day then sputtered the next (after base idle reset and sitting one night)...
 

2L8ULUZ2

Will kiss Moderator ass for title
Founding Member
Sep 24, 2000
3,033
14
99
WNC
May 18, 2005
#2
  • May 18, 2005
  • #2
Take your ignition module off and take it to a parts store and have them test it. No spark and no fuel tells me that it is probably the module and they are notorious for going without any notice.
 

S/CBlack95GT

New Member
Apr 6, 2003
2,018
0
0
Tampa Palms, FL
May 18, 2005
#3
  • May 18, 2005
  • #3
Do you hear the pump buzz when you turn the key to the on position?
 

brentwoodboy

New Member
Nov 25, 2002
472
0
0
Brentwood, TN
May 18, 2005
#4
  • May 18, 2005
  • #4
Yep it primes.
 

S/CBlack95GT

New Member
Apr 6, 2003
2,018
0
0
Tampa Palms, FL
May 18, 2005
#5
  • May 18, 2005
  • #5
brentwoodboy said:
Yep it primes.
Click to expand...

Most likely not a fuel problem then. Checking the spark is next.
 

94-302-vert

Active Member
Aug 16, 2004
1,947
2
36
NE CT
May 18, 2005
#6
  • May 18, 2005
  • #6
You already did the reality check on all connecotrs, vacuum lines etc that had to be removed for that intake swap?

The coil is getting voltage or no?

Sounds vacuum or MAF connector to me.

Chris
 
M

michael66899

New Member
Jun 30, 2004
26
0
1
May 18, 2005
#7
  • May 18, 2005
  • #7
I am also having some similar problems in that I'm not getting any spark. How should I check the coil to see if theres any voltage there? Thanks guys
 

brentwoodboy

New Member
Nov 25, 2002
472
0
0
Brentwood, TN
May 18, 2005
#8
  • May 18, 2005
  • #8
OK, I finally got it started and running great, even took it for a rip. Then it was idling and i was messing with the timing and it died. Now, if I have the key on (car off) and turn the dizzy around and go past a certain point, the car ""clicks". I hear all the elctrical stuff come on, its weird. The I try to start it again, and it will start then just die.
 

CBZGT50

New Member
Apr 21, 2005
171
0
0
St Louis area
May 18, 2005
#9
  • May 18, 2005
  • #9
Try aligning the dizzy with a #1 TDC, ensure proper wire routing and check that MAF to TB tube. If that is off, the car will hardly idle. If I remove a dizzy and stupidly forget to mark it, I always bring the #1 to TDC on compression stroke using a long screwdriver. Once the piston starts to go down set it back to the TDC. Insert the Dizzy with the rotor pointing to #1 on the cap. Lock it down, re run all the wires, try to start. Ignition has to be perfect for these cars to run but the maf to TB tube HAS to be there. My tube came off the other day and I could bearly get my car started until I opened the hood and found the stupid tube had slipped off the TB.

Also, I really believe this is timing because your car will run on four cylinders, it would be rough but would run. Yours is not running at all.
 

brentwoodboy

New Member
Nov 25, 2002
472
0
0
Brentwood, TN
May 18, 2005
#10
  • May 18, 2005
  • #10
But its weird because it will strat and rev for like 5 seconds very smoothly, then sputter, then die. I tried it with my MAF and IAC diconnected, same thing...

BTW how did u use the long screwdriver in regards to TDC? Did you put it in the plug hole?
 
You must log in or register to reply here.

Similar threads

J
Engine Stalling
  • josh40tay
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
204
Fox 5.0 Mustang Tech Oct 21, 2026
JD1964
M
Bad starter?
  • mason5.0
  • Oct 6, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
251
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 6, 2026
General karthief
J
Having fuel issues
  • Jbands2v
  • Nov 2, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
80
SN95 4.6L Mustang Tech Nov 2, 2026
LILCBRA
T
Help with a 95 5L crank no start
  • TheBubbaJoe
  • Nov 4, 2025
  • 1994 - 1995 Specific Tech
Replies
3
Views
576
1994 - 1995 Specific Tech Nov 5, 2025
AeroCoupe
D
Running both lean and rich with O2 heat codes
  • Danceswithfire5
  • Aug 30, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
181
SN95 V6 Mustang Tech Sep 5, 2026
apple99Mustangdude
A
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?