• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

BILL 302 COME TO THIS THREAD

  • Thread starter Thread starter jeremey thomas
  • Start date Start date Jun 2, 2006
J

jeremey thomas

New Member
Feb 23, 2006
142
1
0
scottsboro alabama
Jun 2, 2006
#1
  • Jun 2, 2006
  • #1
bill from gadsden hopefully you can help me somemore with this.my car is a 94 teal gt thats been completely converted to 96 cobra body panels with steeda wing.it was stolen with engine parts stripped.so this is where it started.the shortblock was the only thing left in the engine bay,computer was gone air bags were gone.so i bought a running 94 black on black gt 5 spd drove it home and stripped it of everything.put rebuilt e-7s on because i didnt want to take a chance of ruining a new set of edelbrock heads i just bought.i rebuilt the short block my self and a man from my local machine shop told me to coat the cylinder walls with p b blaster to keep moisture off of them.anything else you need to no about this ask and ill tell you.i have to much invested in this car know to go any further without fixing the problem.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jun 2, 2006
#2
  • Jun 2, 2006
  • #2
do you know for sure the heads were rebuilt...
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jun 2, 2006
#3
  • Jun 2, 2006
  • #3
i might be over reacting about the heads and such all the temps,pressures are in spec and motor has no signs of knocking,overheating ect... have you tried to drive a short distance to see if smoke clears and if you do keep a good eye on the water temp.... or you can stop here and run a pressure test on the coolant system..
 
J

jeremey thomas

New Member
Feb 23, 2006
142
1
0
scottsboro alabama
Jun 2, 2006
#4
  • Jun 2, 2006
  • #4
i started to pull out of the drive way and the temp started to go up.however,i forgot to burp the system so until i check that tomorrow i wont know for sure
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jun 2, 2006
#5
  • Jun 2, 2006
  • #5
ok it can be difficult to bleed the system but the best way is to buy a thermostat with a bleeder hole at the top of the thermostat but if you have one without this hole you can drill a small hole at the top of the thermostat and it will help with bleeding do you know what i'm talking about????
 
J

jeremey thomas

New Member
Feb 23, 2006
142
1
0
scottsboro alabama
Jun 2, 2006
#6
  • Jun 2, 2006
  • #6
the heads had a valve job,new springs,valves themselves were ground.thats about it.i didnt want to spend a lot on the heads as i had bought the edelbrocks.probably should have put them on i nthe first place by the way.im going to check your car out on car domain.i have my old 90 model triple white vert on there.in one of the pictures you can see my 94 in the back ground.
 
J

jeremey thomas

New Member
Feb 23, 2006
142
1
0
scottsboro alabama
Jun 2, 2006
#7
  • Jun 2, 2006
  • #7
yeah ive seen them with the bleeder,i dont think the one i installed has one.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jun 2, 2006
#8
  • Jun 2, 2006
  • #8
it is alot easier to bleed system with the bleeder valve mine didnt have one and i drilled a small hole in the top of the thermostat and i have never had to bleed or had and bleeding problems....hope everything goes well i will be on stangnet tommorrow after 2:30 pm...and thanks for checking out my ride i have recently added a compucar wet kit 90 shot of nitrous to my stang.....i have not added this to stangnet yet...


 

Attachments

  • 5-18-06nitrousinstall010.webp
    34.6 KB · Views: 127
  • 5-18-06nitrousinstall003.webp
    36.4 KB · Views: 101
  • 5-18-06nitrousinstall002.webp
    33.4 KB · Views: 114

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jun 3, 2006
#9
  • Jun 3, 2006
  • #9
i am ready for an update.....
 
You must log in or register to reply here.
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?