• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Car still bucking

  • Thread starter Thread starter Mafia Mustang
  • Start date Start date Apr 25, 2007
M

Mafia Mustang

Member
Sep 17, 2006
111
0
17
Arizona
Apr 25, 2007
#1
  • Apr 25, 2007
  • #1
My car still is bucking unless I let it warm up. But I relocated my Act and I have some pics so tell me what you think.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 25, 2007
#2
  • Apr 25, 2007
  • #2
Not pretty, but it should work. The perferred methout is solder the wires and cover them with heat shrink. Another layer of larger heatshrink tube or wire loom covers the outside of the wires to protect them. When it is done correctly, you can't tell that the wires have bee spliced.



How I did it:
If you are very clever, you will find that the ACT connector comes apart so that you can remove the pins. A very small screwdriver releases the lock in the front of the center insert, while another small screwdriver inserted in the back pushes it out. Once the center insert is out of the connector shell, the pins come out easily. New pins are available from AutoZone in a $5 electrical pin kit for Fords. Crimping the pins on the extender wires saves you from having to splice them twice: once to put the connector on and once to extend the wires.

6 ft black 18 gauge wire
6 ft green 18 gauge wire
6 ft 1/4" heat shrink tubing
1 ft 3/16" heat shrink tubing

Measure the 2 extender wires & cut them to length, crimp one set of pins on them. Then mate up the extender pins with the wiring harness & slide the 3/16" heat shrink tubing over them & shrink the tubing. Then slide the 1/4" heat shrink tubing over the pair of wires and shrink the tubing. When you are done you'll have about 1" of wire left without heat shrink tubing on it to strip & crimp the new pins on. Stick the new pins in the old connector shell, assemble it and you are done. It looks as good as factory. Some wire loom can be used to enhance the "Factory Look".
 
M

Mafia Mustang

Member
Sep 17, 2006
111
0
17
Arizona
Apr 25, 2007
#3
  • Apr 25, 2007
  • #3
ya yours looks good, factory look.
 
You must log in or register to reply here.

Similar threads

9
Car bucks
  • 91stangman
  • Mar 30, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
343
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 19, 2026
Mindseye007
C
Drivetrain Clutch chatter on 66 mustang
  • Coolfords
  • Oct 21, 2026
  • Classic Mustang Specific Tech
Replies
0
Views
85
Classic Mustang Specific Tech Oct 21, 2026
Coolfords
C
C
Engine Idle cuts out
  • claypoolxx
  • Mar 7, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
25
Views
1K
Fox 5.0 Mustang Tech Jul 24, 2026
alutwon
Engine Coolant boiling in hose?
  • Teen'93stang5.0
  • Jun 3, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
352
Fox 5.0 Mustang Tech Jun 8, 2026
Mustang5L5
Strange timing issue
  • 92 Bimini Blue
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
22
Views
739
Fox 5.0 Mustang Tech Oct 20, 2026
rednotch
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?