Electrical Changing from 65 gauge cluster to 66 gauge cluster

65fastbackresto

Active Member

Apr 13, 2007

1,229

7

39

AR

Feb 19, 2013

#1

• Feb 19, 2013

• #1

Ok guys been awhile since I been on here but getting geared up to get some things done. I have a 5 gauge cluster from a 66 mustang I want to put in my 65 that has the old cluster with the sweeping speedometer.

I have an Autometer guage set under the dash with water, oil, and amp gauge. So I think all I need to work are fuel, speedometer, and background lighting on the new 66 gauges.

I`m sure alot of you guys have done this upgrade to their cars, I`d love to hear some good ideas on how to do this, and of course I`d like to hear anything that gone wrong while doing this, as breaking things I`m working on seems to be the best talent I`ve shown thus far.

 

horse sence

15 Year Member

Nov 29, 1999

12,262

8,113

233

Wile Coyote's stunt double

Feb 19, 2013

#2

• Feb 19, 2013

• #2

the mounting tabs will have to be bent forward a little to work with the 66 cluster,
you may have to slice a little at both sides of each tab ,the last one i did i just bent them. the cluster wireing will be different from 65 -66

 

Mr67Stang

Active Member

Feb 10, 2007

117

7

28

Fayetteville, NC

Feb 20, 2013

#3

• Feb 20, 2013

• #3

I had a '66 for a while that had bad/spliced and diced wiring under the dash. I got my hand on a complete and great condition '65 under dash wiring harness. Guess what? They are totaly different. was not trying to switch gauge clusters but as I recall, the '65 harness would not work with the '66 guage cluster. Take a look though since you already have the cluster.

 

65fastbackresto

Active Member

Apr 13, 2007

1,229

7

39

AR

Feb 20, 2013

#4

• Feb 20, 2013

• #4

Well somethings going to give, after all, all I need is working speedometer, fuel gauge, and dashlights.

 

Smitten65

Member

Jan 7, 2011

57

4

19

FL

Feb 21, 2013

#5

• Feb 21, 2013

• #5

The dash lights will work, fuel gauge, temp, hi-beam light and spedometer also. The turn signal for 65 has two wires (left and right) into the same bulb. You will need a new bulb holder (actually, two) and need to separate the wires to run to the two bulb holders. The oil pressure gauge will need to be rewired and the switch itself replaced. The pressure switch is bigger than the 65 one and will need an extention to attach to the block. They are available from most part vendors. The ammeter, however, will be a dead gauge unless you convert (or replace) and wire it for volts.

 

65fastbackresto

Active Member

Apr 13, 2007

1,229

7

39

AR

Mar 15, 2013

#6

• Mar 15, 2013

• #6

Well it`s mounted in the dash, and with the advice I had from you guys about a little trimming here and there it`s looking pretty good. I would have to say this was really easy compared to what I thought it was going to be like. Thanks guys again.

 

Smitten65

Member

Jan 7, 2011

57

4

19

FL

Mar 16, 2013

#7

• Mar 16, 2013

• #7

I don't think you said if your 5 gauge cluster was from a 65 or 66 but if from a 66, I am told you CAN make the ammeter work, even with an upgraded, more powerful alternator, if you have done that also. The 66 ammeter bis a 'shunt' style ammeter that you could wire up to detect current flow. I'm not sure if it can be done with the 65 5 gauge cluster, but all you would need to do on the 66 is put an additional wire in parallel with the existing wire that goes to the battery terminal on the solenoid. Run it from the alt to the gauge and then back out to the battery. Some current will flow through that wire when charging, the bulk of the current through the heavier gauge wire charging the battery . I have not done this yet but plan on doing so later this spring.

 

65fastbackresto

Active Member

Apr 13, 2007

1,229

7

39

AR

Mar 20, 2013

#8

• Mar 20, 2013

• #8

I think it`s a 66 I`ll check it out and see if I can make that work. Thanks.

 

Smitten65

Member

Jan 7, 2011

57

4

19

FL

Mar 25, 2013

#9

• Mar 25, 2013

• #9

Thanks, blkfrd! That is the specific information I needed but didn't have. I was going to try to do this beofe mounting the cluster. This makes it easy now to get a working ammeter!