• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-

Cobra Single blade Throttle Body

  • Thread starter Thread starter bditty50
  • Start date Start date Feb 1, 2010
B

bditty50

Member
Jun 20, 2005
170
0
16
Tampa, Florida
Feb 1, 2010
#1
  • Feb 1, 2010
  • #1
I was looking at a single blade throttle body from accufab. What are the benefits of single blade vs. dual blade? Is there any chance of losing low end with one of these 1900 cfm throttle bodies?
 

Rickyll7

Member
Dec 16, 2005
718
4
19
Feb 1, 2010
#2
  • Feb 1, 2010
  • #2
What engine setup do you have?

How much power do you have and plan to have?

What will flow into it? (what CAI)

What will it flow into? (what Plenum/intake manifold)
 
B

bditty50

Member
Jun 20, 2005
170
0
16
Tampa, Florida
Feb 1, 2010
#3
  • Feb 1, 2010
  • #3
I'm looking to get a procharged 96 cobra and I'm looking into tbs. I plan on the 600 range after rebuild with forged internals. Stock cobra intake.
 

Rickyll7

Member
Dec 16, 2005
718
4
19
Feb 1, 2010
#4
  • Feb 1, 2010
  • #4
I don't know what the stock cobra intake manifold looks like, but if it has a dual bore inlet to match a dual bore tb, then a single blade tb could cause a loss in hp due to lose of aerodynamic flow and an unchanged flow area.

Otherwise, I would think that single blade may be worth a few ponies at 600 rwhp...

Check out the KB website. They do a lot of testing on stuff like this.

http://kennebell.net/techinfo/ford-techinfo/Cobra_LightningTechTips.pdf

"9. OVAL THROTTLE BODY +10HP
No HP at 400, 4HP at 450, 8HP at 500, 10HP at 550."

Results will vary some with a centri, but the trend will remain the same.

And you can throw it in the trash if your intake manifold isn't cut for an oval TB, or you can port your manifold to match.

I forgot one more thing... the oval tb wouldn't even open if the manifold is a dual bore inlet. The manifold would have to be ported for it to work anyway if it is a dual bore inlet. You may also need to look at your IAC valve location and make sure it isnt incorporated into the part that needs to get cut out.
 
You must log in or register to reply here.

Similar threads

A
Catch can questions.
  • AngryH58
  • Sep 26, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
175
1996 - 2004 SN95 Mustang -General/Talk- Sep 29, 2026
squeak93
2001 SVT Cobra slow return to idle speed
  • phil2001svt
  • Oct 21, 2026
  • SVT Tech Forum
Replies
3
Views
166
SVT Tech Forum Nov 2, 2026
phil2001svt
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
328
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
M
94 Mustang gt throttle body
  • Mike3
  • Jul 26, 2025
  • 1994 - 1995 Specific Tech
Replies
6
Views
546
1994 - 1995 Specific Tech Sep 2, 2025
revhead347
S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
399
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?