• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Distributer (Timing) Quick help

  • Thread starter Thread starter Synned
  • Start date Start date Apr 6, 2007
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 6, 2007
#1
  • Apr 6, 2007
  • #1
Whats up guys
Well I'm putting my car back together after an intake swap, and the car was running crappy so I tried pulling the dist., cranking till compression.
Problem is, there are two timing strips, one right after another.
They both start at 0, and end at 30, with the second one about an inch after.
Problem is, it seems everytime I crank till compression, its passed the first 0.
Are these two timing strips BTDC and ATDC????
I know jrichker will be in here in a sec. Thanks guys
 

95opal

5 Year Member
Nov 16, 2004
449
20
39
Apr 6, 2007
#2
  • Apr 6, 2007
  • #2
Yes those are BTDC and ATDC. To the right of the 0 is BTDC.
 
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 6, 2007
#3
  • Apr 6, 2007
  • #3
95opal said:
Yes those are BTDC and ATDC. To the right of the 0 is BTDC.
Click to expand...

So I want to crank it and get it exactly to the 0 BTDC?

The SECOND strip beginning is where I want it??
Or do I want it at the first strip? The beginning of the first strip. That makes sense...but I dont get how BTDC starts at 0 and ends at 40.

Everytime I start trying to get TDC at #1, it usually passes those marks. Can I turn the motor by hand backwards?
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Apr 6, 2007
#4
  • Apr 6, 2007
  • #4
Synned said:
Everytime I start trying to get TDC at #1, it usually passes those marks. Can I turn the motor by hand backwards?
Click to expand...

Yes you can turn it backwards but always go back aways the turn it forward by hand again up to where you need it.
 
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 6, 2007
#5
  • Apr 6, 2007
  • #5
SO for the two timing strips

Kind of look like this
<<<<<<<<<<<<<<<<MOTOR ROTATION<<<
---------BTDC--------..............----------ATDC------
0 10 20 30 40 ............0 10 20 30 40


I want the pointer at 0 BTDC? Or are my timing marks made up and not correct...cause I could barely see
 
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 6, 2007
#6
  • Apr 6, 2007
  • #6
bump
 

4G-KDMP

10 Year Member
Jul 23, 2005
935
19
39
CA
Apr 6, 2007
#7
  • Apr 6, 2007
  • #7
---------BTDC--------..............----------ATDC------
0 10 20 30 40 ............0 10 20 30 40
^

here
 
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 6, 2007
#8
  • Apr 6, 2007
  • #8
Thanks guys
I was just wondering if someone could explain to me why the motor hits 0* BTDC before it hits 40*?
Are my timing marks off in my head? The ATDC makes sense.
 
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 7, 2007
#9
  • Apr 7, 2007
  • #9
Okay, I'm going to try this when I get home from work today.
Pull the dist out.
Pull #1 out.
Crank till compression...when compression look at timing marks.
Usually I'm around:

---------BTDC--------..............----------ATDC------
0 10 20 30 40 ............0 10 20 30 40

^^^^^^

That point...or so. Should I spin the motor clockwise to get it back to 0* BTDC?
In my head, timing marks that look like this
---------BTDC--------..............----------ATDC------
40 30 20 10 0 ............0 10 20 30 40

make much more sense. But then again...I don't know a whole lot about this stuff
 
S

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
Apr 7, 2007
#10
  • Apr 7, 2007
  • #10
anyone?
 

ALMOST STOCK

Founding Member
Sep 23, 2000
1,250
41
88
CA.
Apr 7, 2007
#11
  • Apr 7, 2007
  • #11
Not trying to be a smart ass but are you sure you’re pulling the #1 plug and not the #5 plug?
Are you rotating the engine by hand or using the starter?
The reason I’m asking is because if you’re using the starter to rotate the motor by the time you hear the compression it’s usually gone past the zero timing mark.

Remove the #1 plug, then with a breaker bar and a short extension and the correct socket rotate the engine until you feel the air escape through the #1 plug hole, if you don’t feel any air escaping but you see the pointer on the 0 timing mark that means your on the exhaust stroke not the compression stroke, just keep rotation the engine until you feel all the air escape. I’ll even stick a long pencil in the #1 plug hole and watch it as it comes to the very top and if I see if start to go back down II know I’ve gone to far.

At this point try dropping the distributor in, remember the teeth on the cam and distributor are angled so the distributor will need to be rotated to compensate.
When the distributor drops in you could be ahead or behind the #1 plug wire on the distributor cap just pick it up and re stab it so that you will line up with the #1 plug.
One last thing….. if the distributor points to the #1 plug but the distributor won’t full seat more than likely your not lined up on the oil pump shaft. Hold the distributor and slightly rotate the motor again and the oil pump shaft will rotate enough to let the distributor fully seat.
To double check everything (if you use a pencil remove it) and rotate the engine again until you feel the compression start to exit the #1 plug hole and watch to see where your timing mark is and the check the to make sure you’re on the #1 plug wire.

Reinstall the #1 plug put the distributor cap on, snug but do not tighten the distributor bolt, set up your timing light, remove the spout connector , start the engine and set the correct timing by moving the distributor or what ever timing you chose, then tighten the bolt on the distributor and plug in the Spout connector.

View attachment 390805

View attachment 390806

I hope this helps and makes some since?
 

4G-KDMP

10 Year Member
Jul 23, 2005
935
19
39
CA
Apr 7, 2007
#12
  • Apr 7, 2007
  • #12
that pic of the timing marks is exactly how it should look.
 
You must log in or register to reply here.

Similar threads

Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
500
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
B
'03 GT Fuel Pump/Pressure/Delivery Issue
  • Brodach
  • Oct 21, 2025
  • SN95 4.6L Mustang Tech
Replies
8
Views
1K
SN95 4.6L Mustang Tech Oct 31, 2025
gkomo
Engine 1990 LX 5.0L EFI Mustang Fuel Management Problems - HELP!
  • 5.0LXStanger
  • May 25, 2025
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
45
Views
3K
Fox 5.0 Mustang Tech Jul 11, 2025
5.0LXStanger
D
94 GT cold start takes a long time cranking. Help!
  • DeanS
  • Aug 6, 2024
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
537
1996 - 2004 SN95 Mustang -General/Talk- Aug 10, 2024
Noobz347
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
473
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?