• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Distributor gear problems...

  • Thread starter Thread starter Canimakeit
  • Start date Start date Jul 21, 2008
C

Canimakeit

New Member
Jun 15, 2004
4
0
1
Jul 21, 2008
#1
  • Jul 21, 2008
  • #1
357W ina 89 25th an GT. TW heads 202/160 ported, Super victor intake, 585 lift 290dur comp cam with 15 firing order, MSD dizzy, hard ARP oil pump shaft, melling HV oil pump.

whew, Hbeam rods, JE pistons, stock crank. Internal Balance 28oz.


So, I put the motor in the car and broke it in with NO problems, none. Sound's AWESOME and runs awesome. I go through the valves one day, bumping the starter over to get each to TDC. After I do this I try to fire the car up and no oil pressure or fire, so, I pull the Dizzy *knew exactly what happened from experience.

Bare in mind that after break in* 3 days/ 3 20 minute runs* I adjust valves and thats ALL I did different, WHILE adjusting valves is when it happened.

I had JUST had it running before adjusting the valves and it was running perfect with PERFECT oil pressure, never misfired. This happened WHILE I was bumping the engine to get each cyl to TDC.

So, I got another distro gear from O'Reallys, install it, change oil AND filter. With drain plug out I poor a whole QT of motor oil in the valve cover AND in the distro hole.

Fired the car back up and sounds great again and ran for 5 minutes, took distro back out to check gear, its shined where its wearing already.

This is a FLAT TAPPET comp cam custom grind.

Is the HV oil pump doing this? wrong distro gear? clearance problems? This motor was put together by me and a good friend after a well known shop done the work. The distro its self is the MSD billet and doesn't have alot of play anywhere * no more then normal*

It did this both to the MSD and O'really gear.

Just hoping someone has a suggestion, it's been 7 long years since this car has been out and this is very frustrating. Trying to get back in the game.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Jul 21, 2008
#2
  • Jul 21, 2008
  • #2
The only thing that comes to mind is the same thing that you're considering, which is the distributor gear being incorrect. If you're running a flat tappet cam, you need the cast iron gear. The steel gear, which I'm assuming you may have on the MSD distributor, is meant for a roller cam. The pitch on the teeth are different, and fortunately, the teeth are harder on the cam gear vs. the distributor, so you should be pretty safe just swapping to a new gear. It's possible that there could be clearance issues, but it would likely be too much, causing the distributor to not fully seat. In some cases, material needs to be removed from the end of the shaft, where it engages the oil pump driveshaft, in order to allow the teeth to engage each other.
 
You must log in or register to reply here.

Similar threads

P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
173
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
706
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
00 4.6L V8 new clutch won’t go into gear when on?
  • Timboslice
  • Aug 15, 2026
  • The Welcome Wagon
Replies
3
Views
234
The Welcome Wagon Aug 21, 2026
Noobz347
M
Bad starter?
  • mason5.0
  • Oct 6, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
243
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 6, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?