• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Do I need my EGR?

  • Thread starter Thread starter dec322
  • Start date Start date Mar 4, 2006
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
Mar 4, 2006
#1
  • Mar 4, 2006
  • #1
I just replaced the injectors on my car and noticed the egr doesn't have a tube running into it. There is a place for a tube but its gone. The smog equippment has been deleted.

Also, I found a hose that the previous owner had tucked away under the intake. I don't know where it goes.....One end is connected to the "canister" (looks to have two chambers) behind the passenger side headlight....the other end is just flapping around.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Mar 4, 2006
#2
  • Mar 4, 2006
  • #2
dec322 said:
I just replaced the injectors on my car and noticed the egr doesn't have a tube running into it. There is a place for a tube but its gone. The smog equippment has been deleted.

Also, I found a hose that the previous owner had tucked away under the intake. I don't know where it goes.....One end is connected to the "canister" (looks to have two chambers) behind the passenger side headlight....the other end is just flapping around.
Click to expand...
EGR and the smog pump are 2 dif systems. The egr gasses are routed internally through the stock intake manifold; no external tubes are needed.
There is no power gain to be found by removing the egr, and possible economy losses and part throttle drivieability issues can result.

It sounds like some modification of the fuel evap can system was done by the previous owner. That cannister is filled with carbon, similar to what is used in fish tank filters. This can catches fuel vapors from the fuel tank, and stores them in the carbon until the motor is running. When the motor starts the vapors are purged from the can, and burned in the intake charge. I don't beleive the stock system had the outlet from the can routed directly to the intake. It should have run to the intake box?

jason
 
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
Mar 4, 2006
#3
  • Mar 4, 2006
  • #3
vristang said:
EGR and the smog pump are 2 dif systems. The egr gasses are routed internally through the stock intake manifold; no external tubes are needed.
There is no power gain to be found by removing the egr, and possible economy losses and part throttle drivieability issues can result.

It sounds like some modification of the fuel evap can system was done by the previous owner. That cannister is filled with carbon, similar to what is used in fish tank filters. This can catches fuel vapors from the fuel tank, and stores them in the carbon until the motor is running. When the motor starts the vapors are purged from the can, and burned in the intake charge. I don't beleive the stock system had the outlet from the can routed directly to the intake. It should have run to the intake box?

jason
Click to expand...


Hmm....so there isn't supposed to be any tubes going into the egr? Thats fine with me.

Well, it doesn't go directly into the intake. He just had the end of the tube hidden under the intake (right above the fuel injectors on the driver side). So, I'm just look for the source (unless the canister is the source, in which I'll be looking for where the tube should end).
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Mar 4, 2006
#4
  • Mar 4, 2006
  • #4
black vacuum line comes from gas tank and goes to charcoal canister, then one from there and to under the upper intake where u mentioned
 

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
Mar 4, 2006
#5
  • Mar 4, 2006
  • #5
There is a vacuum line that goes to the EGR valve. It has a 90* elbow on it and the line comes from the passengers side fender. Behind the strut tower.

 

Attachments

  • engine22.webp
    41.7 KB · Views: 180
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
Mar 4, 2006
#6
  • Mar 4, 2006
  • #6
onefstsnake said:
There is a vacuum line that goes to the EGR valve. It has a 90* elbow on it and the line comes from the passengers side fender. Behind the strut tower.

Click to expand...


Ok....thanks for the picture. I'll check that out tomorrow.

I saw a place on the bottom of the intake (driver side) for a vacuum line. The previous owner has capped it off. I'll have to get a longer line b/c the one that is not connected is too short now.
 

Attachments

  • engine22.webp
    41.7 KB · Views: 199

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
Mar 4, 2006
#7
  • Mar 4, 2006
  • #7
I ran the car for a while without the EGR hose connected and didnt notice much if anything...

Make sure you get a nice rubber line, since the stock Ford stuff is hard plastic junk...

90% of my vacuum lines have shattered...
 
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
Mar 5, 2006
#8
  • Mar 5, 2006
  • #8
onefstsnake said:
I ran the car for a while without the EGR hose connected and didnt notice much if anything...

Make sure you get a nice rubber line, since the stock Ford stuff is hard plastic junk...

90% of my vacuum lines have shattered...
Click to expand...


Yeah, the car runs pretty good. Every now and then I get a little bit of a surging idle. I've have yet to really look for it so maybe as I fix these little things, I will accidently fix the surge.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 5, 2006
#9
  • Mar 5, 2006
  • #9
See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine/

Diagram courtesy of Tmoss & Stang&2birds

 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Mar 5, 2006
#10
  • Mar 5, 2006
  • #10
Note Richker/Moss' diagram -- it's not a VACUUM hose that goes to the egr valve; a vacuum hose goes to the EVR (EGR valve regulator); a hose then runs from the OUTPUT PORT of the EVR to the EGR valve; the ecu determines when vacuum is delivered to the EGR valve by actuating the EVR.
 
You must log in or register to reply here.

Similar threads

B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
527
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
F
Electrical From scratch: alternator wiring
  • fox racer v2
  • Jun 23, 2025
  • Fox 5.0 Mustang Tech
Replies
0
Views
688
Fox 5.0 Mustang Tech Jun 23, 2025
fox racer v2
F
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
851
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
J
Emission problems
  • jls.zmmr
  • Feb 5, 2026
  • 1994 - 1995 Specific Tech
Replies
2
Views
343
1994 - 1995 Specific Tech Feb 7, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?