• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

egr probs!!

  • Thread starter Thread starter Mr. Rustypwnz
  • Start date Start date Jun 10, 2007

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Jun 10, 2007
#1
  • Jun 10, 2007
  • #1
Hello, my 86gt didnt have the egr on it when I bought it, so like 2 weeks ago i put it on, along with the temp sensor unit, which tells the computer when to back off the timing and such. I put it on and it idles perfect, a little low, about 650-700ish with the oil press about 25 on a hot day ( explorer pump ) anyway it was running purdy well until today, I went and filled it up and got on it a little in 2-4th anyway after that is ran well for about 3 miles, I took it on a little drive about 20 miles tops, it starts bucking while driving, and while idling its about 20psi on the oil, and it starts knocking, not really bad but noticeable!! I pull into our neighbor hood and it shuts off right when Im pulling into the drive, and wont crank back up, fuel pump sounds really healthy, like it just got hit by a bolt of lightning. anyway before I put this thing back on it would have a wandering idle, but cuise awesome, and have great power!! but with this on it idles pretty good, but drives like crap, but pulls good, but knocks now. Anybody ever have this happen or this just common with bad egr's? Im about to drive it without this pos hooked up and take the temp sensor thing off and see if it runs better. It was running right at 195deg. when I got to the house.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 10, 2007
#2
  • Jun 10, 2007
  • #2
Dump the codes and see what the computer says is wrong…Codes may be present in the computer even if the Check Engine light isn’t on.

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/







IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Wal-Mart.

Or for a nicer scanner see http://www.midwayautosupply.com/pc-7208-90-equus-digital-ford-code-reader-3145.aspx – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $30.
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Jun 10, 2007
#3
  • Jun 10, 2007
  • #3
ill pull em in a few!! thanks
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Jun 10, 2007
#4
  • Jun 10, 2007
  • #4
got code 84, which is the egr regulator. The others were 81 82 85 and 95. but I think I have found teh problem, I took the vacuum port out of the bottom of the intake, and plugged it up, and im using a 3/4" line going to the vaccum tree, and running the lines off of there, do you think its actually giving the egr too much vacuum, and keeping it open all the time? thus driving like crap?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,374
18,121
224
Massachusetts
Jun 10, 2007
#5
  • Jun 10, 2007
  • #5
Well the EGR doesn't draw vacuum from the manifold. It draws it through some solenoids located on the passenger rear fender area. These solenoids only open the EGR at part throttle and close it at idle and WOT, so it does not see constant vacuum.

If you have it hooked up to the vacuum tree, then it will not operate correctly
 

cjones

Founding Member
Jul 20, 2002
1,561
0
37
Avondale, AZ
Jun 10, 2007
#6
  • Jun 10, 2007
  • #6
do you have the air pump hooked up??

codes 81,82 are Air Injection circuit faults.

85 Evap Canister purge - do you have the evap canister hooked up??

95 right side air always upsteam. again, do you have the air injection hooked up??

84 EGR Vent circuit fault. as Mustang5l5 said, you need to connect the EGR solenoids.

i'll post the vac diagrams soon.
 

cjones

Founding Member
Jul 20, 2002
1,561
0
37
Avondale, AZ
Jun 10, 2007
#7
  • Jun 10, 2007
  • #7
Definitions:

VRESER - Vac Resivoir

EVR - EGR Vac Regulator aka EGR solenoid code 84

CPRV - Evap Canister Purge Valve code 95

CAN - Evap Canister

Dump - AIR Dump (to atmosphere) soleniod

DIV - AIR Direction Soleniod - switches air between Upstream(behind heads when engine cold) and Down stream (to cats when engine is warm)

ABV and ACV are valves for the AIR system

AIR - Air Injection - Smog Pump

edit VCK V - Vacuum check valve
 

Attachments

  • 1986-EmissionVacDiagram.webp
    25 KB · Views: 123

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 11, 2007
#8
  • Jun 11, 2007
  • #8
Some basic theory to clarify how things work is in order…

The EGR shuts off at Wide Open Throttle (WOT), so it has minimal effect on performance. The addition of exhaust gas drops combustion temperature, increases gas mileage and reduces the tendency of the engine to ping. It can also reduce HC emissions by reducing fuel consumption. The primary result of EGR usage is a reduction in NOx emissions. A custom chip or Tweecer tune is the only way to disable the EGR in the computer’s programming.

The EGR system has a vacuum source (line from the intake manifold) that goes to the EVR, computer operated electronic vacuum regulator. The EVR is located on the back of the passenger side shock strut tower. The computer uses RPM, Load. and some other factors to tell the EVR to pass vacuum to open the EGR valve. The EGR valve and the passages in the heads and intake manifold route exhaust gas to the EGR spacer (throttle body spacer). The EGR sensor tells the computer how far the EGR valve is open. Then computer adjusts the signal sent to the EVR to hold, increase or decrease the vacuum. The computer adds spark advance to compensate for the recirculated gases and the slower rate they burn at.

There should be no vacuum at the EGR valve when at idle. If there is, the EVR (electronic vacuum regulator) mounted on the backside of the passenger side wheelwell is suspect. Check the vacuum line plumbing to make sure the previous owner didn’t cross the vacuum lines.

Diagram courtesy of Tmoss & Stang&2birds. (the diagram says 88 GT, but the EGR part is the same for 86-93 Mustangs)


The EGR sensor is basically a variable resistor, like the volume control on a radio. One end is 5 volt VREF power from the computer (red/orange wire). One end is computer signal ground (black/white), and the middle wire (brown/lt green) is the signal output from the EGR sensor. It is designed to always have some small voltage output from it anytime the ignition switch is the Run position. That way the computer knows the sensor & the wiring is OK. No voltage on computer pin 27 (brown/lt green wire) and the computer thinks the sensor is bad or the wire is broken and sets code 31. The voltage output can range from approximately .6-.85 volt.


EGR test procedure courtesy of cjones

to check the EGR valve:
bring the engine to normal temp.
connect a vacuum pump to the EGR Valve
apply 5in vacuum to the valve.
if engine stumbled or died then EGR Valve and passage(there is a passageway through the heads and intake) are good.
if engine did NOT stumble or die then either the EGR Valve is bad and/or the passage is blocked.
if engine stumbled, connect vacuum gauge to the hose coming off of the EGR Valve
snap throttle to 2500 RPM (remember snap the throttle don't hold it there).
did the vacuum gauge show about 2-5 in vacuum?

if not, check for manifold vacuum at the EGR vacuum valve.
if you have manifold vacuum then connect vacuum gauge to the EGR valve side of the vacuum valve and snap throttle to 2500 RPM.
should read about 2-5 in vacuum


Late Model Restoration has the Ford Racing M-12071-N302 kit with the EGR valve & sensor along with the ACT & ECT sensors for $45. See http://www.latemodelrestoration.com/iwwida.pvx?;item?item_no=M12071N302 1&comp=LRS for more details


Thermactor Air System (smog pump & codes 44, 94, 81, 82)

The Thermactor air pump (smog pump) supplies air to the heads or catalytic converters. This air helps break down the excess HC (hydrocarbons) and CO (carbon monoxide). The air supplied to the catalytic converters helps create the catalytic reaction that changes the HC & CO into CO2 and water vapor. Catalytic converters on 5.0 Mustangs are designed to use the extra air provided by the smog pump. Without the extra air, the catalytic converters will clog and fail.

The Thermactor air pump (smog pump) puts air into the heads when the engine is cold and then into the catalytic converters when it is warm. The Thermactor control valves serve to direct the flow. The first valve, TAB (Thermactor Air Bypass) or AM1 valve) either dumps air to the atmosphere or passes it on to the second valve. The second valve, TAD (Thermactor Air Diverter valve or AM2 valve) directs it to the heads or the catalytic converters. The air serves to help consume any unburned hydrocarbons by supplying extra oxygen to the catalytic process. The computer tells the Thermactor Air System to open the dump valve at WOT (wide open throttle) minimizing engine drag. The dump valve reduces the parasitic drag caused by the smog pump to about 2-4 HP at WOT.



Computer operation & control for the Thermactor Air System
Automobile computers use current sink technology. They do not source power to any relay, solenoid or actuator like the IAC, fuel pump relay, or fuel injectors. Instead the computer provides a ground path for the positive battery voltage to get back to the battery negative terminal. That flow of power from positive to negative is what provides the energy to make the IAC, fuel pump relay, or fuel injectors work. No ground provided by the computer, then the actuators and relays don't operate.

One side of the any relay/actuator/solenoid in the engine compartment will be connected to a red wire that has 12-14 volts anytime the ignition switch is in the run position. The other side will have 12-14 volts when the relay/actuator/solenoid isn't turned on. Once the computer turns on the clamp side, the voltage on the computer side of the wire will drop down to 1 volt or less.

In order to test the TAD/TAB solenoids, you need to ground the white/red wire on the TAB solenoid or the light green/black wire on the TAD solenoid.

To test the computer, you can use a test light across the TAB or TAD wiring connectors and dump the codes. When you dump the codes, the computer does a self test that toggles every relay/actuator/solenoid on and off. When this happens, the test light will flicker.

Code 85 - CANP solenoid - The Carbon Canister solenoid is inoperative. Check vacuum lines for leaks and cracks. Check electrical wiring for loose connections, damaged wiring and insulation. Check solenoid valve operation by grounding the gray/yellow wire to the solenoid and blowing through it.
The computer provides the ground for the solenoid. The red wire to the solenoid is always energized any time the ignition switch is in the run position.

Charcoal canister plumbing - one 3/8" tube from the bottom of the upper manifold to the rubber hose. Rubber hose connects to one side of the canister solenoid valve. Other side of the solenoid valve connects to one side of the canister. The other side of the canister connects to a rubber hose that connects to a line that goes all the way back to the gas tank. There is an electrical connector coming from the passenger side injector harness near #1 injector that plugs into the canister solenoid valve. It's purpose is to vent the gas tank. The solenoid valve opens at cruse to provide some extra fuel.

It does not weigh but a pound or so and helps richen up the cruse mixture. It draws no HP & keeps the car from smelling like gasoline in a closed garage. So with all these good things and no bad ones, why not hook it up & use it?

The code 95 has two different definitions: if you got the code 95 with the key on, engine not running, it is a fuel pump circuit fault. If you got it with the key on, engine running it is an Thermactor Air System fault.
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Jun 11, 2007
#9
  • Jun 11, 2007
  • #9
dam, I dont have the vacuum regulator, there's where my problems are!! My car when i bought it didnt have it when i bought it!!! It all makes sense now, I dont have any of the smog stuff either which is the 81 82 and 85 codes, the fuel pump was hard wired by the previous owner so It always has the 95 code.

Thanks everyone for the help!!!
 
You must log in or register to reply here.

Similar threads

Engine Keeping O2 sensors lit with long tube headers
  • keel
  • Jul 30, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
285
Fox 5.0 Mustang Tech Aug 21, 2026
Qtrhrse23
7
Engine Random hanging idle
  • 706 Saleen
  • Feb 11, 2026
  • Fox 5.0 Mustang Tech
Replies
9
Views
860
Fox 5.0 Mustang Tech Feb 19, 2026
86HO5.0
8
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
734
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
B
Help! Fox with idle issues
  • bbarton
  • Sep 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
310
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 12, 2026
AeroCoupe
M
Idle control problems
  • miser143
  • Aug 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
213
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 29, 2026
DadLife0724
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?