• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum

engine prob after rain

  • Thread starter Thread starter seths99cobra
  • Start date Start date Jan 29, 2010

seths99cobra

Member
Aug 31, 2009
92
0
7
afghanistan
Jan 29, 2010
#1
  • Jan 29, 2010
  • #1
i was driving down a two lane road tonight and the road had standing water all the way across it for about 100ft and i had no where to go so i trucked it and i got threw it and then the car started spitting and spuddering real bad and shut off. car cranked right up but idled bad and when i revd it it sounded horrible then died again. i pulled the intake tub off on the side of the road and it had some water in it. i managed to get a scan tool on it and it said misfire in cyl 8. i let it run for a little while then it started running a little better and i drove it around to see if it worked it out of the system for a little while. while on my way back home it started making a slite ticking noise. do you guys think i collapsed the plug? and the ticking noise could it be a valve tapping as the result? what do i need to do to check it or to fix it? thanks for the inputs.
 

2BADSTANGS

Member
Jun 19, 2008
385
1
18
Colorado
Jan 29, 2010
#2
  • Jan 29, 2010
  • #2
Do you have an aftermarket cold air intake on your Cobra?
 

COBRA90GT

Mustang Master
Sep 22, 2001
6,654
0
87
HOCKEYTOWN ® , MI
Jan 30, 2010
#3
  • Jan 30, 2010
  • #3
Time to start pulling sparkplugs. DO NOT START THE ENGINE UP AGAIN IN THE MEANTIME


You want to allow the water in the engine to "dry up." Do not start the engine. Drain the oil and inspect it for small metallic parts...

If the engine inhaled a significant amount of water, you will need to evacuate any trapped water (because water does NOT compress - it will only lead to parts breakage).

Pull all the sparkplugs (also disconnect the fuel pump, or its fuse to ensure no fuel), crank the engine over, and check to see if any water comes out of the sparkplug holes. Have a buddy help.

It can get pretty labor intensive if you have to pull the intake and use a shop vac to suction out any trapped water, but it's better than destroying your engine. Unfortunately, that "new ticking" sound you heard is probably a clue that means it's time to start saving up money for a possible rebuild down the road...

G'luck.



Not flaming, but hindsight being 20/20 (and for others out there):

It would have been wise to not start the engine back up after it died on you. Have it towed home where you can work on it or to a shop if the engine dies or shuts off due to hydrolocking.
 

cobranator

Founding Member
Sep 16, 2001
90
0
7
Kelowna, B.C. Canada
Jan 30, 2010
#4
  • Jan 30, 2010
  • #4
2BADSTANGS said:
Do you have an aftermarket cold air intake on your Cobra?
Click to expand...

That's the first thing I thought of as well......if he has one and I think he does he sucked in some water and hydrolocked the engine, not good at all.

I'm gonna go out on a limb here and say he has a JLT cold air intake in the fender.
 

seths99cobra

Member
Aug 31, 2009
92
0
7
afghanistan
Jan 30, 2010
#5
  • Jan 30, 2010
  • #5
yeah i have a jlt cai. i checked the oil and there was no water in the oil. but i am gonna drain it here in a bit to be certin and safe. i pulled all the plugs and they all looked fine and they were all sparking. but the ticking noise dont happen all the time it comes and goes. pullin the intake out and sucking up water if there is any is no problem can do that in minutes from experience of pulling it off 4 5 times in a week once. but what is the ticking noise anyway?
 

cobranator

Founding Member
Sep 16, 2001
90
0
7
Kelowna, B.C. Canada
Jan 30, 2010
#6
  • Jan 30, 2010
  • #6
Without actually listening to the engine it's hard to say what the tick is..or is it a knock?.....Again I'm going to go out on a limb here and say you have bent con rod and or a rod bearing fubared and if so there are no easy or cheap fixes for this. More than likely you're looking at an engine rebuild.
 

seths99cobra

Member
Aug 31, 2009
92
0
7
afghanistan
Jan 30, 2010
#7
  • Jan 30, 2010
  • #7
i just changed the oil and no water or metal shavings in it. but the noise can only be heard in the car with a low rev and holding the rev or while drivin in a low gear slowly. more of a ticking or rattle almost sounds like something is loose. i tried listening for it with the hood open and no luck.
 
L

lang williams

New Member
Jun 11, 2003
567
0
0
cleveland, oh
Jan 30, 2010
#8
  • Jan 30, 2010
  • #8
cut the oil filter open an inspect the filtering material for any metal that could indicate problems.
 
You must log in or register to reply here.

Similar threads

B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
737
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
C
Knocking after pull- went away?
  • Connormcclark
  • Oct 6, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
233
1996 - 2004 SN95 Mustang -General/Talk- Oct 6, 2025
gkomo
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
856
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
594
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
380
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?