• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Exhaust mounting problems. need help

  • Thread starter Thread starter ShortThrow50
  • Start date Start date May 30, 2007

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
May 30, 2007
#1
  • May 30, 2007
  • #1
I finally dropped my eng and trans in but came across 2 more dam problems. Im frustrated. I have the summit shorty headers as shown (started running short on cash lol). It seems as though I cant get the passenger side mac o/r h pipe hanger into the holder because if i do put it in the holder it wont reach the header flange or ball (whatever u call it). The drivers side is fine. Im not so sure it is because of the summit headers, they seem legit. I think its because of the tko mounting is further back. Should i just sawzall the hanger and be done with it? My other problem is, for some weird ass reason the h pipes are about 2 - 3 inches from reaching my flowmaster catback. What gives? I ran the same h pipe and catback on my old setup. The cat back stayed mounted on the car. Why and how is this possible. What should i do with that now? Is there some sort of extension i can do? Give me your thoughts on what to do next. I dont think the headers are the culprit, they seem to be the same size as the stock ones. Everything else including dropping the engine in (by myself) went easy. Also, I will never attempt to do a clutch quadrant in a fox again. That pissed me off too but got it done. Thanks. Sorry for the long post





 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
May 30, 2007
#2
  • May 30, 2007
  • #2
i HATE changing my clutch quadrant. i replaced my stock one with a D&D aluminum quadrant, which i broke in 2 months, a few months back. i've since gotten a pro 5.0 one. very sturdy piece. way easier to install, only have to slide it on one of the pedal posts rather than try and shimmy it on to two. ummm, as far as your exhaust, just hack the hangers. i haven't used them since day 1. and your exhaust not reaching now? do you mean your h pipe doesn't reach the flow tubes? if you can't tweak it to get it to fit, i'd say take it to a local muffler shop and have them extend your flow tubes or your h pipe the necessary length. but i still don't see why they don't reach. thats odd.
 

1987stangman

Member
Jul 12, 2006
684
24
19
May 30, 2007
#3
  • May 30, 2007
  • #3
Well, unless your trying using a H that was meant for longtubes then the only thing that comes to mind is the hangar plate that mounts between the tranny tail section and the tranny mount is backwards. There is a left/right indicator on it. As long as the xmember is in the stock spot then thats all it could be. I personally would figure out why it wont reach and would recommend against cutting the hangars.
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
May 30, 2007
#4
  • May 30, 2007
  • #4
1987stangman said:
Well, unless your trying using a H that was meant for longtubes then the only thing that comes to mind is the hangar plate that mounts between the tranny tail section and the tranny mount is backwards. There is a left/right indicator on it. As long as the xmember is in the stock spot then thats all it could be. I personally would figure out why it wont reach and would recommend against cutting the hangars.
Click to expand...

I have tko 600 and it requires you to cut welds on stock crossmemebr and slide crossmember all the way back and re weld. all the mounting points are pushed back. it is the same h pipe i used on my old setup with stock headers. It is a mac made for stock 93 5.0 headers. I understand what your saying though. If it were for long tubes I would have more like a 1 foot gap rather tthan 2 inches
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
May 31, 2007
#5
  • May 31, 2007
  • #5
ttt
 
You must log in or register to reply here.

Similar threads

Surging/stalling! problem or tune?
  • djj62478
  • Oct 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
406
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 14, 2026
KRUISR
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
319
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
856
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
2
new edge coolant leak need advice asap
  • 2vBoogs
  • Tuesday at 8:37 PM
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
77
1996 - 2004 SN95 Mustang -General/Talk- Yesterday at 4:38 PM
Mustang5L5
S
Car shakes when taking off help???
  • STANKYstangs
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
563
1996 - 2004 SN95 Mustang -General/Talk- May 27, 2026
LILCBRA
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?