• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Fan clutch is on it's way out. Replace or go electric?

  • Thread starter Thread starter MYSTICSVT
  • Start date Start date Jun 24, 2005
M

MYSTICSVT

Founding Member
May 16, 2001
349
0
16
Meridian, Idaho
Jun 24, 2005
#1
  • Jun 24, 2005
  • #1
My Stang's temp is slowly creeping up at stops. And the A/C pressures are WAY up at idle. It also doesn't seem to be pulling much air at idle. So I'm assuming my fan clutch is not performing at its best. Should I replace it with a new one or go electric? My concerns are cost, reliability, and performance. I'd prefer to go electric. But I'm concerned about the cost and complexity. I'm more than capable of doing some fabrication to make an electric fit. But I'm getting lazy in my old age. So I'd rather it be a bolt-in. Is there any electric fan setup that won't require an alternator upgrade and will work in 110 degree temps with the A/C rolling? Proform maybe? This car is daily driven (approx 50 miles) by my wife, and only has exhaust, intake, and rear gear upgrades. So reliability is paramount. New fan clutch or electric?

FYI, did a search, but I'm looking for some fresh info.
 

LX302

Stanger
Founding Member
Feb 29, 2000
728
6
19
Bethlehem PA
Jun 24, 2005
#2
  • Jun 24, 2005
  • #2
It really comes down to what you really want to do.
If it were mine, I'd just put a new OEM thermatic fan clutch on. Less work.
 

bryanrevans

New Member
Sep 10, 2004
296
0
0
Chicopee,Mass
Jun 24, 2005
#3
  • Jun 24, 2005
  • #3
I did that totaly worthless crap.Just replace the stocker no worries.I did the stuff in my sig wasnt worth it at all!!!!!! But dont take my word for it wait until you are done
 

87TTopGT

New Member
Dec 21, 2003
173
1
0
Jun 24, 2005
#4
  • Jun 24, 2005
  • #4
Electric!
 

slo65

New Member
May 26, 2003
448
0
0
Southern California
Jun 24, 2005
#5
  • Jun 24, 2005
  • #5
put mine in the other week, no problems in temp, plus i installed a cool switch just above my radio, so far so good
 
B

black92gt

New Member
Aug 7, 2001
64
0
0
PA
Jun 24, 2005
#6
  • Jun 24, 2005
  • #6
The proform worked fine for me. $150.00 off of ebay shipped.
 

cardudeusa

Founding Member
Oct 22, 2002
1,744
5
48
Home of the Florida Gators!
Jun 24, 2005
#7
  • Jun 24, 2005
  • #7
If it were me, I would probubly just slap the stock style fan clutch back in. Being its your wifes car. Unless you race it or plan to, I wouldn't go with the electric, being that you are not wanting to spend a whole lot. If you do go with the electric fan I reccomend www.dccontrol.com the fans are a bit on the pricey side, but are worth the money. My fiances car has this on it and the stock alternator. Read up on it and decide what you need to do.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 24, 2005
#8
  • Jun 24, 2005
  • #8
My thoughts: the stock set-up is arguably cheaper to renew, and it works at all times (nice for the Mrs). The stock set up is hard to beat, CFM wise, IMHO.

I am down in Tucson and have had very good results with the following:

New metal replacement metal fan blade. 30 bucks. For the fan clutch, I am using an Imperial HD unit from Autozone. I chose this route because it has a lifetime warranty. Clutches lose a few hundred RPM a year, so the warranty is nice.

Otherwise, if wanting electric, I would go with a Viper fan, were I you. Be sure to have the requisite 3/6 G upgrade before doing so. Like Cardude said, the variable controller is the way to control it, but it is $$ (you mentioned that as a factor).


Good luck.
 

The Shape

Founding Member
Jan 11, 2002
2,224
8
49
East ARKANSAS Delta
Jun 24, 2005
#9
  • Jun 24, 2005
  • #9
Another thing to consider is that the stock alternator is just about maxed with the stock electrical system so adding the electric fan may lead to upgrading the alternator as well. I would just replace the clutch and call it good.
 
You must log in or register to reply here.

Similar threads

S
Preparation for Holley Terminator X install – Foxbody 306 (electrical fan, alternator, MSD Ignition, etc)
  • So_Flo
  • Mar 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 4, 2026
General karthief
D
Engine Is the oem clutch fan always supposed to be running?
  • dqureshi06
  • Sep 13, 2024
  • Fox 5.0 Mustang Tech
Replies
2
Views
252
Fox 5.0 Mustang Tech Sep 13, 2024
Mustang5L5
W
High Cylinder Head Temp - Not Overheating?
  • wtfwork12
  • Jun 26, 2025
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
9
Views
2K
2005 - 2014 S-197 Mustang -General/Talk- Jul 1, 2025
wtfwork12
W
H
New kid on the block
  • HydraX
  • Mar 22, 2025
  • The Welcome Wagon
Replies
17
Views
767
The Welcome Wagon Mar 22, 2025
HydraX
H
S
KNOCK WITH CLUTCH OUT
  • Scwhitten
  • Apr 13, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
249
1996 - 2004 SN95 Mustang -General/Talk- Apr 22, 2025
89ripper
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?