• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

fender/door not flush

  • Thread starter Thread starter ras50gt
  • Start date Start date Mar 1, 2007

ras50gt

Member
Oct 25, 2005
200
2
19
Mar 1, 2007
#1
  • Mar 1, 2007
  • #1
I wanted to see if anyone here has had this problem before and what they did to fix it (check link for pic - under 1993 GT). When I first bought the car almost six years ago, it had the gap from the fender to door. It never really bothered me and the average person wouldn't notice it unless I told/showed him/her. Now that I'm thinking about painting the car and all the mods to come, it pisses me off to look at it. I remember almost not buying the car because of it, but everything else about the car was what I wanted. Anyways, the guy I bought it from mentioned something about a shop jacking the car in the wrong spot. I figured it could be fixed but never cared about it until now. I just want to know if there is anything I can try before taking it to a body shop and probably spending a lot of money. Check out the link for the pictures. I've asked about this a long time ago, someone said to get new bushings for the door, however the door doesn't sag and it opens and closes perfectly, you can see in the pictures that the door alignment is fine. The floor under the car looks fine, doesn't appear to be dented in. Here's the link......

http://new.photos.yahoo.com/ras50gt/album
 
M

Mike92GT

Founding Member
Jan 23, 2002
583
0
0
Florida
Mar 1, 2007
#2
  • Mar 1, 2007
  • #2
This is a common problem, and like you said, it is usually caused by jacking up the car in the wrong spot. Luckily, it is usually and easy fix. Under the car at the bottom portion of the fender, the fender is attached with a 8mm / 5/16th bolt. The bolt is covered up by part of the plastic inner fender liner, so you will need to loosen it some so you can get at the bolt. Try loosening the bolt, many times the fender will straighten itself right out, then just tighten the bolt back up. Sometimes the bottom edge of the fender is bent up, you might need to straigten it all out first with some channel locks or pliers. Good luck
 

ras50gt

Member
Oct 25, 2005
200
2
19
Mar 1, 2007
#3
  • Mar 1, 2007
  • #3
Thanks man, I will give it a try tomorrow. I really hope it turns out to be an easy fix. I can't stand looking at it everytime I get into my car or when washing it.
 

Shakerhood

20+ Year Stangneter
Oct 28, 2004
3,361
211
114
Ohio
Mar 2, 2007
#4
  • Mar 2, 2007
  • #4
Mine stuck out a little and it was caused by a jack being in the wrong spot, I hammered the floor down a little and loosened the small bolt you can see when you open the door and the bolt underneath and it went right into place.
 

ras50gt

Member
Oct 25, 2005
200
2
19
Mar 2, 2007
#5
  • Mar 2, 2007
  • #5
The bolt you can see when opening the door, is that at the top, above the latch? I think I located the bolt underneath, it was just barely covered by the fender liner plastic basically at the end of the liner going towards the back of the car, is this right? I will give it a try tomorrow.
 
You must log in or register to reply here.

Similar threads

Most ridiculous / dishonest work you have heard a shop recommend?
  • SchwarzStock
  • Jul 19, 2026
  • Off-Topic Hangout
Replies
4
Views
153
Off-Topic Hangout Jul 20, 2026
SchwarzStock
S
01 GT DRIVERS SIDE DOOR LOCK CYLINDER LINKAGE
  • Scwhitten
  • May 13, 2026
  • SN95 4.6L Mustang Tech
Replies
3
Views
322
SN95 4.6L Mustang Tech Jun 19, 2026
melo.timo
M
B
A/C Issues
  • Boats90GT
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
215
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
Mcmahst
Paint and Body Rotten moon roof trim
  • Teen'93stang5.0
  • Apr 14, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
237
Fox 5.0 Mustang Tech Apr 15, 2026
Teen'93stang5.0
G
In expensive ceramic coating
  • gray owl
  • Jul 12, 2026
  • Mustang Sound & Shine All
Replies
7
Views
500
Mustang Sound & Shine All Aug 18, 2026
NotaVegetarian
N
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?