• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Fuel line thingie

  • Thread starter Thread starter LaserSVT
  • Start date Start date Jun 23, 2007

LaserSVT

Got FB banned again for saying nards
Founding Member
Nov 29, 1999
9,402
3,548
233
Jun 23, 2007
#1
  • Jun 23, 2007
  • #1
After exausting searching I can not locate the schrader valve on my fuel line, so it must not have the right one. Can I please get help finding a fuel line (feed between the rail and the soft line) so I can hook up a fuel pressure gauge so I can set my fuel pressure.
 

cjones

Founding Member
Jul 20, 2002
1,561
0
37
Avondale, AZ
Jun 24, 2007
#2
  • Jun 24, 2007
  • #2
the valve should be on the fuel rail front right of engine with a black cap over it.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 24, 2007
#3
  • Jun 24, 2007
  • #3
See the metal elbow with the hose attached to it?


Fuel pressure gauge adapter fittings:
http://www.holley.com/products.asp?product=17945NOS AN 4 to 1/16” pipe
http://www.holley.com/products.asp?product=16785NOS 1/16” male pipe to 1/8” female pipe

Or
See http://www.autometer.com/cat_accessorieslist.aspx?pid=10

I made my own pressure gauge and holder. I bought the NOS or Autometer adapter that you screw into the place on the fuel line where the schrader valve goes. You have to remove the Schrader valve, but save it, since you will reuse it. I ran a piece of SS (stainless steel) braided hose to a 1/8” pipe brass tee fitting that I mounted on the fender well by the MAF. I made a mount bracket out of aluminum angle I got from Home depot and bolted it to the fender well. Then I mounted the brass tee to it with some machine screws and a plate. I sandwiched the brass tee between the aluminum angle and a flat piece of aluminum that I trimmed off the extra aluminum angle. Three screws laid out in a triangle pattern go through both pieces of aluminum to clamp the tee in place. Put the Schrader valve in the spare port of the brass tee. I used a cheap industrial gauge from MSC Direct (http://www1.mscdirect.com/ P/N 56468499). It works great and was cheaper than (less than $6) anything Summit had.

If you look through the MSC Direct catalog, you can find any type of gauge you want, including liquid filled. You only need a liquid filled gauge if you mount it directly on the engine. The liquid filling dampens out the vibrations.

You can buy the Autometer Stainless Steel braided hose for like $60. Or a local shop that makes hydraulic hose assemblies can make it for you at a cheaper price. Ordinary low pressure hydraulic hose can be used in place of the Stainless Steel braided hose, the Stainless Steel braided hose just looks nice. I got mine for $4 at a place that sells industrial and military surplus parts of all kinds. The Stainless Steel braided hose goes for about $3.60 a foot and the fittings are probably about $5-$8 each. You can make your own and save some $$$, the shops may have a setup or labor charge to fabricate the hose assembly.







 

LaserSVT

Got FB banned again for saying nards
Founding Member
Nov 29, 1999
9,402
3,548
233
Jun 24, 2007
#4
  • Jun 24, 2007
  • #4
Very nice My old Mustang (89) had it there too, but the new onw (92) does not. Whene I was at Latemodel Restoration yesterday they came out and looked at it and we all figured it must be lines off an older Mustang (86?) so it does not have a schrader valve. I just ordered a brand new second hand set from ebay for $35, it comes with the rail which I dont need but atleast they are the right lines. I also ordered this trick fuel pressure gauge that is electrical so I can mount it inside. I wonder if I need an adapter to hook the sending unit to the scrader valve? Any one know?

Hey jrichker, what kind af mass air meter is that?
 
You must log in or register to reply here.

Similar threads

B
Fuel 1990 installing edelBrock intake
  • Beaker
  • Oct 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
349
Fox 5.0 Mustang Tech Oct 6, 2026
Noobz347
D
Fuel Erratic Fuel Pressure 1985 GT
  • DienstXIV
  • Jan 14, 2026
  • Fox 5.0 Mustang Tech
Replies
16
Views
966
Fox 5.0 Mustang Tech Jan 16, 2026
AeroCoupe
S
Brakes 80 Mustang 4.2 rear chassis brake line for 5 lug conversion!
  • StangPowerLSX510
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
188
Fox 5.0 Mustang Tech Aug 9, 2026
limp
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
537
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
S
thread no longer needed
  • skidad
  • Oct 17, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
156
1996 - 2004 SN95 Mustang -General/Talk- Oct 17, 2026
skidad
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?