Gear Install , SCT 3 , dyno tune, price !

ran260gt · Mar 31, 2008

Made a few phone calls today and got some prices . PA area.

The place I like the most said $720 for gear install , thats gear oil , gear kit , FRPP 4.10 gears and labor !

SCT 3 Tuner for $ 400 .

And I also asked about a Dyno tune that I probably dont really need , that was $ 400 !

So all together that $1520 !

Does that sound pricey , and do I need a Dyno tune yet , only mods I have are in my sig !

Dragstr05 · Mar 31, 2008

A dyno tune wouldnt hurt, but IMO you really dont need it. I'm running nearly identical mods to you, and had a mail order tune loaded onto my X3 at no cost.

See if you cant find someone to help you out with the gears for much cheaper. I had a friend help me with my gears. He did the everything inside, I pulled the axles and such. Did the whole install, with fluid, FRPP 4.10's, rebuild kit and tuner for about $700.

Just FYI, and no I'm not spamming, but go over to americanmuscle.com and it might save you a few bucks. They have a 4.10 gear and tuner kit at a discounted price. Includes oil, but no rebuild kit.

CMEFLY · Mar 31, 2008

You can get your sct xcal3 from don lasoda at lasota racing for 379.00 shipped and he will give you 3 custom tunes for your car at no extra charge. Way better then the canned tunes it comes with and you can save the $400 on a dyno tune.

SaleenGT2001 · Mar 31, 2008

that price is way too high.

i got my gears and had the installed for less than $500. the dyno tune is also way high. i paid $225 for my last tune.

you dont even need a tune for a simple gear swap. just buy an xcal and use the preloaded tunes and correct your cars gear ratio

Winters98GT · Mar 31, 2008

my last gear install was 350 bucks, for gear, oils, labor, and speedcal.

Sounds like they dont like to work or have too much work, cause nobody that is sane would pay that. You can have the rear almost completely built for that.

Sounds like you need to get another shop. Living up north, im sure you have 50 shops within a 1-2 hour drive that are top notch.

TheBocSez · Apr 4, 2008

Thats an expensive gear install, I was quoted 529.00 for an install including all you listed and its on an IRS.

BurningRubber · Apr 4, 2008

$700 is way too high.

You could do it yourself and mess up once and re-do it for less than that.

I paid $300 for my install. That what rebuilding the trac-lok as well as replacing all bearings in the rear end (axle bearings and seals as well).

COramprat · Apr 4, 2008

Although mine were done a while ago I paid 525. Even now I think that is a fair price. 700 just siunds a bit much

Mossberg · Apr 4, 2008

Sounds high to me for what you are getting.

wusthof · Apr 5, 2008

this is a popular place for mustangs up here in Vancouver (remember this is Canada, so everything is more expensive!!!!):

Mustang 1979 to 2004 8.8 Solid Axle & IRS

* New Gearset 3.55, 3.73, 3.90, 4.10, 4.30 - Motive Gears
* New Bearing Kit Includes Carrier Bearings, Pinion Bearings, Crush Sleeve, Pinion Seal.
* Remove & Install & Setup Gears, Bearings & Tighten Up Posi - Replace Up To 2 Worn Discs With Good Used Ones.
* New Fluid & Friction Modifier

*>$649.99 Parts & Labour<

* Add $50 For Ford Motorsport
* Add $125 For Ford Motorsport 4.10, 4.30 & 4.56
* Add $125 For New Posi Kit - Clutch Pack Kit & Installed
* Add $125 For New Axle Bearings & Seals & Installed
**All Above Are Add Ons Apply Only To Gear Install - $649

*** Warranty - 1 Year On Parts Defects
* * * * * * * * * * *- 1 Year On Labour Defects

Mention Your Vancouvermustangs.com Members Name & Save $50

*** We'll Install Your Gears For $275 Labour Only.

MyBloodRunsBlue · Apr 5, 2008

i got my gears and install for 450...dyno tune for 400 is reasonable...xcal3 for 400 is reasonable as well

BlownStangGT · Apr 6, 2008

I know CJ pony parts is a little hike from you, they are in Harrisburg, but they charge $300.00 labor for gears, Ford Racing 4.10's are $179.99 from them, gear kit from them is $38.95, and fluid is not ot much, so thats $518.94 plus fluid, so that saves a few pennies www.cjponyparts.com

ran260gt · Apr 6, 2008

Thanks everybody for the replys !

I think im going to hold off on the Dyno tune til I have a few more mods !

I can get a SCT X3 for $375 at a few places online and I found on Latemodel Restoration Supply a gear kit .
FRPP 4.10
Master bearing kit
1 bottle of friction modifier
2 bottles of Royal Purple gear oil , for $260 and I found a clean performance shop to do the install for $300

Thats $935 total . thats maybe the best im going to get , the biggest fear I have is finding a good shop to do the work , I dont want to go crazy finding the cheapest place and get what I paid for !

Gear Install , SCT 3 , dyno tune, price !

ran260gt

New Member

Dragstr05

New Member

CMEFLY

New Member

SaleenGT2001

Well-Known Member

Winters98GT

Whoop...whoop-whoop-whoop-whoop...GANGNAM STYLE!!!

TheBocSez

New Member

BurningRubber

COramprat

...I can take it. I think.

Mossberg

Active Member

wusthof

Member

MyBloodRunsBlue

New Member

BlownStangGT

REPEAT

ran260gt

New Member

Similar threads

Gear Install , SCT 3 , dyno tune, price !

New Member

New Member

New Member

Well-Known Member

Whoop...whoop-whoop-whoop-whoop...GANGNAM STYLE!!!

New Member

...I can take it. I think.

Active Member

Member

New Member

REPEAT

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency