• Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-

Help!! Misfiring After Install of Remanufactured 3.7L Engine

  • Thread starter Thread starter mercury83
  • Start date Start date Jun 29, 2019
M

mercury83

New Member
Jun 16, 2007
1
0
0
Jun 29, 2019
#1
  • Jun 29, 2019
  • #1
I recently swapped a high mileage 3.7l ford engine for a remanufactured 3.7l ford engine in my 2011 v6. It included new spark plugs. When I got the car back, the check engine light started to flash and read misfires on two cylinders. It only happened when I aggressively accelerated on the highway, leading a mechanic to suspect bad coil packs.

We then immediately replaced four of those coils including the ones connected with the cylinders mentioned in the code. For a day it was fine, then the check engine light came back on and the misfiring became more noticeable and consistent. When I had the code read, it said misfire in cylinder 3 (one of the replaced coils), and a random misfire. Before we replaced the coils it would blink until I pulled over and stopped and restarted the car, then it would disappear. After those replacements it stays on and the car bucks and is constantly misfiring. It can’t reach high rpm’s and it vibrates on idle. I have all new spark plugs and 4 new coils. Whatever the issue is I’m suspecting it’s electrical/computer based. I’m badly in need of ideas because I’m not a mechanic and I can’t afford to keep throwing money at this. Any ideas on what this could be?
 

JmP6889928

You might slide out if you are going too fast.
5 Year Member
May 18, 2019
3,535
4,508
153
67
Southwest Michigan
Jul 10, 2019
#2
  • Jul 10, 2019
  • #2
Did your old engine misfire? What was the reason for the replacement? I never put new plugs in a rebuild-I always use plugs I know were firing correctly before and drive it a while until the break in is complete and then change for new. New plugs can be a blessing and a curse, because you always think "these are new plugs, they can't be bad", but that's not always the case.

I would remove all plugs and take a reading. If one or more are wet, they you have other issues which could be valve seals or even piston rings that haven't sealed as of yet.
 
You must log in or register to reply here.

Similar threads

M
Help! 2003 GT misfire when hot
  • Modular03
  • Feb 10, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
413
SN95 4.6L Mustang Tech Feb 13, 2026
Mustang5L5
A
Check Engine codes jumping around
  • azactor
  • Jan 9, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
191
1996 - 2004 SN95 Mustang -General/Talk- Jan 10, 2026
gkomo
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
229
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
M
Misfire
  • Mike3
  • May 30, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
94
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 30, 2026
Mike3
M
R
Misfire at high rpm! Help
  • Ryanm2018gt
  • Jan 2, 2026
  • 2015 - 2023 (S550) Mustang -General/Talk
Replies
9
Views
978
2015 - 2023 (S550) Mustang -General/Talk Jan 17, 2026
highplace11
H
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?