• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

HELP!

  • Thread starter Thread starter shlby123
  • Start date Start date Jun 18, 2006
S

shlby123

Founding Member
Apr 19, 2002
579
0
0
Dallas
Jun 18, 2006
#1
  • Jun 18, 2006
  • #1
Trying to figure our to pull out the entire center console on my '89 and no matter what gear i put the car in, i cant seem to get around the shifter to get it out! Anybody know the trick?
 
S

shlby123

Founding Member
Apr 19, 2002
579
0
0
Dallas
Jun 18, 2006
#2
  • Jun 18, 2006
  • #2
I dont know if its because of the rubber near the base of the shifter, but I can budge it without cracking the plastic.
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Jun 18, 2006
#3
  • Jun 18, 2006
  • #3
What about removing the stick?
 
S

shlby123

Founding Member
Apr 19, 2002
579
0
0
Dallas
Jun 18, 2006
#4
  • Jun 18, 2006
  • #4
The instructions for the project say that all I had to do was place the stick in one the further back gears but after trying 2, then 4, and then reverse it just doesnt seem possible without cracking that flimsy ass console. Honestly I dont know how it could be done without removing the shifter...
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 18, 2006
#5
  • Jun 18, 2006
  • #5
Saleen0679 said:
What about removing the stick?
Click to expand...
My thoughts exactly. With most shifters (including the stock noodle), pull two bolts and the handle will come off. Now you should be good to go.

Good luck.
 
S

shlby123

Founding Member
Apr 19, 2002
579
0
0
Dallas
Jun 18, 2006
#6
  • Jun 18, 2006
  • #6
looks to be no other way to get it out than to remove the shifter completely but I just thought it weird that in the Mustang Monthly Article where it shows you the walkthrough on how to swap out cores, it just says put the shifter down and the console would pull right out....but then again I've found one or two other inconsistencies with that article too...
 
S

shlby123

Founding Member
Apr 19, 2002
579
0
0
Dallas
Jun 20, 2006
#7
  • Jun 20, 2006
  • #7
Ok. Im at the next obstacle in the project. I've removed all three of the HVAC bolts that are supposed to hold that pain in the ass in place. But the bod wont move and after unscrewing the top of the box I cant even get enough clearance but to just peek at the heater core. Very aggravating because I dont know what else to unbolt or move or whatever to get full access to the core.

ANd whats the easiest way to drain all the coolant and such?
 

Mustang928

Founding Member
Jan 2, 2000
538
0
16
ORANGE COUNTY, CALIFORNIA
Jun 20, 2006
#8
  • Jun 20, 2006
  • #8
From what I remember there are screws/bolts holding the radio bracket in place.. have you removed those.

Also I believe there are one bolt on each side(bottom) of the console.
 
S

shlby123

Founding Member
Apr 19, 2002
579
0
0
Dallas
Jun 20, 2006
#9
  • Jun 20, 2006
  • #9
ok got that taken care of, now how do I take off the hoses under the hood? I cant figure it out? I tried yanking them off but they dont budge!!!
 

Bolt on 5.0

Founding Member
Jun 26, 2002
302
0
17
Suffolk, NY
Jun 20, 2006
#10
  • Jun 20, 2006
  • #10
if the heater hoses are stuck try to twist them or use a right angle pick and stick it between the heater core tubes and the hose. Somtime a pain but twist and pull.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Jun 20, 2006
#11
  • Jun 20, 2006
  • #11
I use a pair of channel locks to TWIST them around the core fitting. Once they break loose, you can pull them right off.
 
You must log in or register to reply here.

Similar threads

J
Interior and Upholstery NEED HELP FINDING SHIFTER PLATE
  • Jschallitz
  • Nov 12, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
85
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 13, 2026
rednotch
C
Electrical Under dash wiring
  • ChicagoMustang
  • Apr 17, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
222
Fox 5.0 Mustang Tech Apr 17, 2026
AeroCoupe
S
CHANGING BRAKE PADS
  • Scwhitten
  • Jun 8, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
20
Views
848
1996 - 2004 SN95 Mustang -General/Talk- Jun 12, 2026
nickyb
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
345
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
Drivetrain Broken clutch cable- what it looks like
  • JulianR
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
899
Fox 5.0 Mustang Tech Aug 10, 2026
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?