• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Here's the "footwork" video you all wanted...

  • Thread starter Thread starter Killercanary
  • Start date Start date Nov 10, 2004
  • 1
  • 2
  • 3
Next
1 of 3 Next Last

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Nov 10, 2004
#1
  • Nov 10, 2004
  • #1
I put up a video the other day of an in car shot of me going through the gears, the only thing was you couldn't see the "footwork" going on in the last video. Well... here it is. I had my wife go with me on our lunch break and do a little more in car video. Its like 30 some degrees here, so the nitto's didn't hook as well as they did in the last one as you'll hear when I hit 2nd gear. Well, I hope this helps some of the other guys that are trying to learn to shift quicker what is going on with the pedals... again this is EXACTLY how I drive at the track. I don't powershift it as you can see I lift (although VERY quickly) between every gear change. Anyway... enjoy. I am actually suprised the tires held in 1st for as cold as it is out, even though I just rolled into it. For the guys wanting to know how to "launch" if you watch closely as I pull out I launch the same way... you'll see my right foot move very little and my left foot operating the clutch does most of the work. This is a poor example as I couldn't pull out with any decent RPM but it will give you the idea.

Paul's Foot Work!

PS- I made a "fly by" video too, but I don't have time to upload it right now. I will later tonight.
 

gcomfx.com

Founding Member
Oct 22, 2002
3,690
0
56
Republic, MO
Nov 10, 2004
#2
  • Nov 10, 2004
  • #2
Nice.... What's the rev in 2nd?
 
1

1hot5.0

Founding Member
Sep 6, 2002
1,615
0
0
Surprise, Arizona
Nov 10, 2004
#3
  • Nov 10, 2004
  • #3
Can't wait to see the fly by video.
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Nov 10, 2004
#4
  • Nov 10, 2004
  • #4
gcomfx.com said:
Nice.... What's the rev in 2nd?
Click to expand...


I was shifting right at 6000rpms on the stock tach, or did you mean the sound of the motor as soon as I hit 2nd? If that's what you mean that was the tires spinning as soon as I hit 2nd and then them grabbing.
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Nov 10, 2004
#5
  • Nov 10, 2004
  • #5
I had my wife take 2 in car videos. This one is a close up of my feet and I wasn't going to show it, but it will give you another idea of what is going on. I didn't like it at first because it was almost TOO close, but now I think this one is the best.

Pauls footwork 2 EXTREME CLOSEUP
 

Joes95GT

New Member
Jan 23, 2003
3,132
1
0
Delaware
Nov 10, 2004
#6
  • Nov 10, 2004
  • #6
I like how you can hear the motor as the tires break loose in second. Those are very helpful videos. Do you move your seat up at all when you race? For me, I've always found that moving the seat up slightly helps me stab the clutch a little better. I'm also assuming by how fast you shift the clutch doesn't get completely disengaged? My fastest shifts always come when I don't disengage the clutch ("half-clutching").

Christ Paul, you should open up a library for all these "educational" videos you're making. We'll call it PBS - Paul's Broadcasting System.

Joe
 

gcomfx.com

Founding Member
Oct 22, 2002
3,690
0
56
Republic, MO
Nov 10, 2004
#7
  • Nov 10, 2004
  • #7
Killercanary said:
or did you mean the sound of the motor as soon as I hit 2nd? If that's what you mean that was the tires spinning as soon as I hit 2nd and then them grabbing.
Click to expand...

I couldn't tell if it was that or you slipping the clutch some, but yeah that's what I was talking about.
 

blksn955.o

Founding Member
Mar 15, 2002
3,263
0
66
st.louis mo 314
Nov 10, 2004
#8
  • Nov 10, 2004
  • #8
damn man nice car and nice driving skills.......

I second the PBS..............

We could add a vid. of someone powershifting to give a view of how that is done as well.. call it driving FAQ.
 

gcomfx.com

Founding Member
Oct 22, 2002
3,690
0
56
Republic, MO
Nov 10, 2004
#9
  • Nov 10, 2004
  • #9
Paul.... write up a tutorial and I'll add it to my site along with the vids.
 

nmcgrawj

Advanced Member
Sep 28, 2003
3,651
4
68
Indianapolis, IN
Nov 10, 2004
#10
  • Nov 10, 2004
  • #10


I hope i can drive that well one day.....Good Job! Thanks for the videos!
 

ARed1995GT

New Member
Dec 9, 2003
401
0
0
Boca Raton, FL
Nov 10, 2004
#11
  • Nov 10, 2004
  • #11
when i first saw this i was like damn, hows the wife gonna get a clear shot of his feet while hes shifting and going full throttle.... damn, makes me realize i have to do lots more practice with shifting
 

Black95GTS

Active Member
Jan 8, 2004
1,644
3
38
Marlborough, MA
Nov 10, 2004
#12
  • Nov 10, 2004
  • #12
I thought I was a young Jedi, but now realize I am still a Padowan Learner.

tell your wife we said thanks, its money that she skipped lunch break to film her husband shifting.
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Nov 10, 2004
#13
  • Nov 10, 2004
  • #13
Joe, at the track I move the seat WAY up so I have to do a lot less "reaching" and shifting with my arm as you mentioned earlier. Its NOT comfortable, but it definitely helps. I do TOTALLY disengage the clutch though... it get pushed the whole way to the floor on every one of those shifts in the video, if I don't it will NOT go into gear. Watch my left leg and you'll see how far down it goes.

Paul- what kind of tutorial do you want me to write? I mean stuff happens so quick that its hard to tell someone what is going on. Its just a quick stab and grab. I do leave off the throttle, I do push the clutch pedal all the way down, I cup the shifter and pull it back on the 1-2, then I palm the back of the shifter for the 2-3, and then reposition my hand to cup and pull the shifter back. If you do this you will virtually eliminate missed shifts (unless you have driveline issues like me). If you "force" the shifter you'll miss the gate and it won't go in.


I'm glad you guys like these videos. I know from looking at some of the combos on here and the dyno numbers they are making that they should be faster than they are. Shifting is a big part of that... think about it when you are shifting you are NOT accelerating, so the quicker you can get it done the better.

In case the above links go down, here are the same videos... Try the above links FIRST.

Paul's foot work


Paul's foot work closeup


Here's my "fly by" I just did it for fun... the tires AGAIN did not hook when I hit 2nd!
Paul's "fly by"
 

onebad95

Sherriff of Bling King County
Jul 22, 2002
1,237
0
37
At the end of the track waiting for you !!
Nov 10, 2004
#14
  • Nov 10, 2004
  • #14
PBS = Paul's Bar Setting
 

mystang94gt

New Member
Jun 14, 2004
951
0
0
Bay Area, CA
Nov 10, 2004
#15
  • Nov 10, 2004
  • #15
Wow thats some driving paul. Makes me wish I had a stick.

Damn AODE
 

WhiteStallionGT

Member
Aug 19, 2004
465
0
17
Northern VA / VT
Nov 10, 2004
#16
  • Nov 10, 2004
  • #16
Damn it exceeded bandwitdth.
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Nov 10, 2004
#17
  • Nov 10, 2004
  • #17
there are other links here that work...
 

go.rei GT

New Member
Nov 29, 2003
267
0
0
Az
Nov 10, 2004
#18
  • Nov 10, 2004
  • #18
Nice vids Paul. I wish my car revved that fast...3.08's
That is exactly how I shift, except for the 3-4 shift. On that one I use a little more wrist (see the first vid). Instead of cupping from the side on that one I cup higher up, not quite directly on top. That way you can flick your wrist back at the same time as you pull back, gaining a little more speed (and you really don't have to worry about missing 4th). Now I want to know what I can do at the track lol.
As far as people needing to practice, I developed my skills from always being late to school, and hauling @ss to make it to class on time. The fast shifting was a biproduct of necessity.
 

OrangeMustangGt

Founding Member
Mar 7, 2002
1,976
0
36
Cape Cod, MA
Nov 10, 2004
#19
  • Nov 10, 2004
  • #19
omg man, woah someday i will rip like that lol. but seriously tommorow im gonna go and shift the hell outta mine and try and be like you.
 

OinkAodeOink

Founding Member
Jun 5, 2002
3,026
1
0
Daytona bch, Florida
Nov 10, 2004
#20
  • Nov 10, 2004
  • #20
Man your wife must really love cars, or you..lol

I hope to someday meet a woman of such character!
 
  • 1
  • 2
  • 3
Next
1 of 3 Next Last
You must log in or register to reply here.

Similar threads

S
1998 Mustang Gt Rattling sound, cannot locate. Video included
  • studerman1
  • Mar 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
8
Views
240
1996 - 2004 SN95 Mustang -General/Talk- Apr 1, 2026
studerman1
S
S
01 GT DRIVERS SIDE DOOR LOCK CYLINDER LINKAGE
  • Scwhitten
  • May 13, 2026
  • SN95 4.6L Mustang Tech
Replies
3
Views
158
SN95 4.6L Mustang Tech Jun 19, 2026
melo.timo
M
Eastern North Carolina Autocross Events!
  • Warhorse Racing
  • Feb 23, 2026
  • Regional Forums and Event Information
Replies
0
Views
347
Regional Forums and Event Information Feb 23, 2026
Warhorse Racing
K
Electrical 2000 GT Intermittent Engine Shutdown In Motion - DTC U1262
  • kenster1092
  • Apr 13, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
205
SN95 4.6L Mustang Tech Apr 24, 2026
squeak93
T
Fox Convertible top issues
  • TDM389
  • Feb 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
313
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 15, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?