• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

horrible vibration/shaking

  • Thread starter Thread starter Allpro_5.0
  • Start date Start date Feb 8, 2007

Allpro_5.0

New Member
Jan 10, 2007
5
0
0
Feb 8, 2007
#1
  • Feb 8, 2007
  • #1
yesterday i decided it was time for a brake over haul. so i replaced my front rotors, my drums, pads and shoes. while i was at it i put in new inner and outer wheel bearings on the front (possible suspects). and yesterday morning the car ran smoothly but i completed the job got everything together and now when i get up to about 60mph my whole cars starts vibrating real hard. it wont do it until i hit 60. i cant tell if its from the front the whole car seems to be just shaking. any suggestions?
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 8, 2007
#2
  • Feb 8, 2007
  • #2
lock nut?

im not sure but maybe you didnt tighten the nut on the outside of the rotor enough? i know from the factory you can take them off with your fingers. the not designed to be locked down hard. but i imagine not enough could cause vibration.
 
S

Silvers

New Member
Jan 4, 2007
51
0
0
Feb 8, 2007
#3
  • Feb 8, 2007
  • #3
Somethings loose, check bearings and lug nuts. Check the drive shaft too.
 

Allpro_5.0

New Member
Jan 10, 2007
5
0
0
Feb 8, 2007
#4
  • Feb 8, 2007
  • #4
i checked

i thought about the nut so i took the cover off and made sure it was snug but not to tight and its still doing it. and i dont think its my drive shaft because it wasnt doing it earlier that day it started after i did the brake job.
 
H

HaynStang

New Member
Dec 16, 2006
124
0
0
Portland
Feb 8, 2007
#5
  • Feb 8, 2007
  • #5
What procedure did you use for torquing down the lock nuts? I'd retorque them, they might have come loose after driving.

Check your driveshaft bolts too, they can come loose pretty much out of nowhere. I had a horrible vibration above 50 mph that just came out of the blue one day. One shop told me I had a bad rear wheel bearing and another told me I'd bent a rear wheel. Turned out the driveshaft bolts had backed out nearly all the way. I tightened them down and no more vibration.
 
B

bz393

New Member
Sep 24, 2006
29
0
2
maryland
Feb 8, 2007
#6
  • Feb 8, 2007
  • #6
Could be some out of balance tires. Just an idea.
 
S

Silvers

New Member
Jan 4, 2007
51
0
0
Feb 8, 2007
#7
  • Feb 8, 2007
  • #7
If you have directional tires make sure you didn't put them on backward. Just a thought, I don't know if that will cause a vibration or not.
 

Allpro_5.0

New Member
Jan 10, 2007
5
0
0
Feb 8, 2007
#8
  • Feb 8, 2007
  • #8
torque

i dont think you can torque them past a certain point because that retaining pin has to go in between the sleeve, nut and the spindle the hole has to line up. and i dont think they are gonna make another half turn to get it to the other side to put the pin through.
 

Allpro_5.0

New Member
Jan 10, 2007
5
0
0
Feb 8, 2007
#9
  • Feb 8, 2007
  • #9
tires

and yea my tires are my next check point im hoping i knocked off a wheel weight or something. im gonna have them re-balanced tommorrow
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 8, 2007
#10
  • Feb 8, 2007
  • #10
the nuts

make sure your rotors are pushed all the way up as to where the seal goes over that little lip and is all the way up against the spindle. cause its a pretty tight fit and if its not all the way up you will have play in it. and im not sure if you can tighten the nut down to hard as you mentioned. i would like to know that myself, maybe someone will chime in and let me know.
 
You must log in or register to reply here.

Similar threads

N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
756
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
J
Severe shaking/vibrations in steering wheel
  • jacket999
  • May 20, 2025
  • SN95 V6 Mustang Tech
Replies
8
Views
1K
SN95 V6 Mustang Tech Jun 1, 2025
NtheGAME
N
S
Car shakes when taking off help???
  • STANKYstangs
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
564
1996 - 2004 SN95 Mustang -General/Talk- May 27, 2026
LILCBRA
H
Strange steering/brake issue
  • Haxmaster
  • Jun 2, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
194
SN95 4.6L Mustang Tech Jun 3, 2026
squeak93
L
95 gt engine vibration
  • lenzgt
  • May 11, 2026
  • 1994 - 1995 Specific Tech
Replies
6
Views
386
1994 - 1995 Specific Tech May 26, 2026
lenzgt
L
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?