• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Installing a Viper keyless entry module and relays.

  • Thread starter Thread starter Fett
  • Start date Start date May 16, 2006

Fett

New Member
Nov 2, 2004
766
6
0
May 16, 2006
#1
  • May 16, 2006
  • #1
I searched and found some info, but just enough to confuse me.

A friend of mine gave me a Viper alarm module that I would like to use to put keyless entry in my 88. Looking at the back of the module it shows constant +, ignition +, -, lock, unlock, horn. I am pretty sure that I could just wire it up as it shows, but from what I am reading it would be smarter to use relays. inline with lock and unlock.

For starters, what rated relays should I use, and exactly how should the be wired up?

After looking at how the stock wires run, the power goes through the right lock button, through both actuators, and through the left button, grounded out on both terminals on the left button....closing the loop.

Would I wire the module between the buttons, after the buttons, or before the buttons?

Thank you.
 

Attachments

  • Untitled-1.psd.webp
    14.4 KB · Views: 637

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 16, 2006
#2
  • May 16, 2006
  • #2
I would use a DEI 451M for ease. You can also just use two Bosch SPDT relays (30 ampers) if that's easier - they both do the exact same thing.

The lock wires can be accessed at the top of the driver side kick panel (remove the panel). THe primary on the wires is pink IIRC and they are of good gauge. The stangs use 5 wire locks as I recall, so wire it accordingly. Do be sure that the common and NC wires go to the right thing (each is connected to one end of the wire you cut. If you wire it backwards, it can take out an actuator.

Post specific questions and myself of the other smart folks can help.

BTW, I applaud you using external relays, even if your module has on-board relays. I do the same - it unburdens the on-boarders.

Good luck.
 
You must log in or register to reply here.

Similar threads

J
89 mustang alarm install to lock and unlock
  • jk66
  • Apr 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
252
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 10, 2026
jk66
J
A
SN95 Multifunction Madness! Need some big brain assistance from you folks
  • Awnaw
  • Oct 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
141
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 10, 2026
AeroCoupe
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
220
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
N
Power door lock motor Question
  • NYFox
  • Mar 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
424
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 17, 2026
NYFox
N
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?