• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Interior lights and door locks 95 mustang GT convertible

  • Thread starter Thread starter Hort
  • Start date Start date Jan 22, 2020
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Jan 22, 2020
#1
  • Jan 22, 2020
  • #1
What a mess! No interior lights and when pushing the unlock switch the bell rings and the fog lights flash! Has anyone experienced this and found a solution?
 

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"
15 Year Member
Nov 29, 1999
14,679
424
154
Boca Raton, Florida
Jan 24, 2020
#2
  • Jan 24, 2020
  • #2
Sorry, got a chuckle out of this. Def got some wiring / ground issues going on.
 

General karthief

wonder how much it would cost to ship you a pair
20+ Year Stangneter
Aug 25, 2016
27,942
10,582
203
polk county florida
Jan 24, 2020
#3
  • Jan 24, 2020
  • #3
Does it have a remote or a aftermarket alarm?
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Jan 24, 2020
#4
  • Jan 24, 2020
  • #4
General karthief said:
Does it have a remote or a aftermarket alarm?
Click to expand...

Dead on. Moreover, did it ever have an aftermarket alarm? Those are usually clipped in (poorly by guys at Circuit City) to the wiring harness that comes down from the ignition switch under the the steering column. Look for evidence of ****y.

Kurt
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Jan 27, 2020
#5
  • Jan 27, 2020
  • #5
VibrantRedGT said:
Sorry, got a chuckle out of this. Def got some wiring / ground issues going on.
Click to expand...
Not only having electric issues but took this long to figure out how to respond on this site!
I would probably be laughing to, so I understand, I was just reaching out to see if this kind of stuff is common for fords and see what ideas would be suggested. I will check for ground issues as suggested, thanks for your help.
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Jan 27, 2020
#6
  • Jan 27, 2020
  • #6
revhead347 said:
Dead on. Moreover, did it ever have an aftermarket alarm? Those are usually clipped in (poorly by guys at Circuit City) to the wiring harness that comes down from the ignition switch under the the steering column. Look for evidence of ****y.

Kurt
Click to expand...
Sorry for the delay can you tell me if mustang was standard with an alarm for 1995 GT’S
another thing I’m questioning is all these clamp in in-line single splices, is that something that ford did to cut costs and time?
 

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"
15 Year Member
Nov 29, 1999
14,679
424
154
Boca Raton, Florida
Jan 28, 2020
#7
  • Jan 28, 2020
  • #7
Hort said:
Sorry for the delay can you tell me if mustang was standard with an alarm for 1995 GT’S
another thing I’m questioning is all these clamp in in-line single splices, is that something that ford did to cut costs and time?
Click to expand...

No and No on both. Somebody has been in there which is why you're having issues.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Jan 28, 2020
#8
  • Jan 28, 2020
  • #8
Hort said:
Sorry for the delay can you tell me if mustang was standard with an alarm for 1995 GT’S
another thing I’m questioning is all these clamp in in-line single splices, is that something that ford did to cut costs and time?
Click to expand...

No, if there are in line butt splices, it's from when someone put an aftermarket alarm in, it failed, and then took it back out and just spliced everything back together. The good news is, it's probably an easy fix. Ford has really good color coding on their wires. Make sure all the colors match on each end, take out butt splice, solder back together. There's a good chance that will fix it.

Kurt
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Jan 28, 2020
#9
  • Jan 28, 2020
  • #9
Thanks for your information I will dig into this mess as soon as I get the car back from the alignment shop, they said something about needing to drill out new holes to move the struts so they could adjust the caster. I think I may have bought a unending can of worms
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Jan 30, 2020
#10
  • Jan 30, 2020
  • #10
Hort said:
Thanks for your information I will dig into this mess as soon as I get the car back from the alignment shop, they said something about needing to drill out new holes to move the struts so they could adjust the caster. I think I may have bought a unending can of worms
Click to expand...

It's an old car man. There's going to be problems. You should the crap we have to deal with on the E30 BMWs we work on.

Yes, you can drill out the struts to adjust the caster, but it's time poorly spent. For what a set of caster/camber plates go for, it's well worth it. It will be easier to adjust, give you a much larger range of adjustment, and look much better.

Kurt
 
Reactions: General karthief

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Jan 30, 2020
#11
  • Jan 30, 2020
  • #11
revhead347 said:
It's an old car man. There's going to be problems. You should the crap we have to deal with on the E30 BMWs we work on.

Yes, you can drill out the struts to adjust the caster, but it's time poorly spent. For what a set of caster/camber plates go for, it's well worth it. It will be easier to adjust, give you a much larger range of adjustment, and look much better. Plus the new caster/camber plates are going replace the current strut mounts which are most like likely worn slap ass out causing the problem in the first place....for about the same price of a new set of strut mounts.

Kurt
Click to expand...
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Jan 30, 2020
#12
  • Jan 30, 2020
  • #12
Thanks for the heads up, unfortunately the alignment shop had it done before I read this so I’m going to buy a set from CJ Pony parts for future use.
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Jan 30, 2020
#13
  • Jan 30, 2020
  • #13
revhead347 said:
No, if there are in line butt splices, it's from when someone put an aftermarket alarm in, it failed, and then took it back out and just spliced everything back together. The good news is, it's probably an easy fix. Ford has really good color coding on their wires. Make sure all the colors match on each end, take out butt splice, solder back together. There's a good chance that will fix it.

Kurt
Click to expand...
You already knew you were right but I wanted to let you know that you were spot on with the aftermarket alarm! These guys should be ashamed of themselves on the pathetic way they installed the piece of junk! Now I have to get this cleaned up and back to norma. Thankful for your help with the diagnosis and a good hot tub!
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Jan 30, 2020
#14
  • Jan 30, 2020
  • #14
Hort said:
Thanks for the heads up, unfortunately the alignment shop had it done before I read this so I’m going to buy a set from CJ Pony parts for future use.
Click to expand...

Well, won't hurt anything really. If they already did it then don't worry about it. I wouldn't buy a set of caster/camber plates until you need them. One of the tricks when I did alignments (this is in the long long ago, in the time before time) was to pull the strut mount down and rotate it to see if that helped before we actually drilled it out.

Kurt
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Oct 15, 2020
#15
  • Oct 15, 2020
  • #15
revhead347 said:
It's an old car man. There's going to be problems. You should the crap we have to deal with on the E30 BMWs we work on.

Yes, you can drill out the struts to adjust the caster, but it's time poorly spent. For what a set of caster/camber plates go for, it's well worth it. It will be easier to adjust, give you a much larger range of adjustment, and look much better.

Kurt
Click to expand...
Here we are 10 months later and scratching my head again! How can something this beautiful act like it is possessed? I have a short in the radio circuit so I pulled the fuse on number 8 to buy some time to get to work on the issue. The car has been sitting in the garage about a week, since I pulled the fuse and I walked out and found the right turn signals flashing tonight! Needless to say I disconnected the battery. Have you ever experienced this? Do you have any suggestions? Your help in January was spot on and very helpful so I thought I would give you a shout if nothing else thought you would get a laugh out of my agony!
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Oct 15, 2020
#16
  • Oct 15, 2020
  • #16
Hort said:
Here we are 10 months later and scratching my head again! How can something this beautiful act like it is possessed? I have a short in the radio circuit so I pulled the fuse on number 8 to buy some time to get to work on the issue. The car has been sitting in the garage about a week, since I pulled the fuse and I walked out and found the right turn signals flashing tonight! Needless to say I disconnected the battery. Have you ever experienced this? Do you have any suggestions? Your help in January was spot on and very helpful so I thought I would give you a shout if nothing else thought you would get a laugh out of my agony!
Click to expand...

Nope, never seen that. Probably just a bad turn signal or emergency flasher switch, or something else stupid like that.

Kurt
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Oct 15, 2020
#17
  • Oct 15, 2020
  • #17
revhead347 said:
Nope, never seen that. Probably just a bad turn signal or emergency flasher switch, or something else stupid like that.

Kurt
Click to expand...
Thanks I’ll be digging in tomorrow morning to try and locate my issues
 
G

greg94

20+ Year Stangneter
Sep 3, 2002
26
1
4
lakeland fl
Oct 17, 2020
#18
  • Oct 17, 2020
  • #18
Hort
I had the exact issue in my 94. This will sound weird as it turned out to be the speedo and printed circuit board on the back of the instrument panel. If you want to test this....unplug the 2 harnesses to the instrument panel. You only need to partially disassemble. Rotate so you can access harness and unplug both. Make sure fuses are good. Then hit the door and interior light. If they work you are closer to finding the short to ground. . Pull the instrument cluster and inspect the printed circuit board for burnout. The number 8 and 12 fuse location in the mustang can create some wired issues.
 
H

Hort

New Member
Jan 22, 2020
9
0
1
Arizona
Oct 17, 2020
#19
  • Oct 17, 2020
  • #19
greg94 said:
Hort
I had the exact issue in my 94. This will sound weird as it turned out to be the speedo and printed circuit board on the back of the instrument panel. If you want to test this....unplug the 2 harnesses to the instrument panel. You only need to partially disassemble. Rotate so you can access harness and unplug both. Make sure fuses are good. Then hit the door and interior light. If they work you are closer to finding the short to ground. . Pull the instrument cluster and inspect the printed circuit board for burnout. The number 8 and 12 fuse location in the mustang can create some wired issues.
Click to expand...
Thanks for the information I will keep it as the next step. HOWEVER I got thinking about how the R front turn light was the only one blinking with everything off. I realized that the emergency flasher is the only way to power the blinker relay, so this morning I activated the emergency lights and then turned them off. Now (this might come back to bite me) but everything went back to normal! Currently I have driven the car around for a few hours and now it is parked back in the garage. I’m checking hourly and so far all is well. It’s going to be a long night!
THANKS AGAIN it’s nice to know that people will share all this weird stuff.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,302
1,645
214
Acworth, GA
Oct 18, 2020
#20
  • Oct 18, 2020
  • #20
Hort said:
Thanks for the information I will keep it as the next step. HOWEVER I got thinking about how the R front turn light was the only one blinking with everything off. I realized that the emergency flasher is the only way to power the blinker relay, so this morning I activated the emergency lights and then turned them off. Now (this might come back to bite me) but everything went back to normal! Currently I have driven the car around for a few hours and now it is parked back in the garage. I’m checking hourly and so far all is well. It’s going to be a long night!
THANKS AGAIN it’s nice to know that people will share all this weird stuff.
Click to expand...

Change that flasher out of principle.

Kurt
 
You must log in or register to reply here.

Similar threads

L
Door pull panels, convertible versus coupe
  • lenzgt
  • Jun 25, 2026
  • 1994 - 1995 Specific Tech
Replies
2
Views
97
1994 - 1995 Specific Tech Jun 25, 2026
lenzgt
L
J
67 mustang interior courtesy light wiring
  • JCuster
  • Jun 9, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
2
Views
90
1965 - 1973 Classic Mustangs -General/Talk- Jun 17, 2026
GypsyR
G
J
89 mustang alarm install to lock and unlock
  • jk66
  • Apr 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
159
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 10, 2026
jk66
J
1
1989 gt both doors wont lock or unlock help.
  • 1989 mustang gt
  • Nov 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
574
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 22, 2025
manicmechanic007
N
Power door lock motor Question
  • NYFox
  • Mar 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
271
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 17, 2026
NYFox
N
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?