• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2.3L (N/A & Turbo) Tech

Kinda in need of help and ideas about problems....

  • Thread starter Thread starter dabazied
  • Start date Start date Dec 14, 2007
D

dabazied

New Member
Dec 14, 2007
2
0
0
Dec 14, 2007
#1
  • Dec 14, 2007
  • #1
Ok. First off I would like to say hi to everyone and let ya know I am new to the whole mustang thing and this forum. Just bout the car about 3hrs ago lol.....

On to the good part(loaded with sarcasm lol)......

Bought an 87 mustang LX 4 banger today for a great price. Here is my issue.... To take off from a dead stop, I have to give it a good amount of gas(but not too much otherwise it just sounds like it is backfiring, struggling, VERY SLOW, and then stalls out) to go. I can't just give it the "normal" amount and I have to ease off the clutch very slowly so that way I can get the perfect amount of RPMs so it'll take off with out doing the stalling thing(whether it be too much or too little). Also, if I floor it it'll do the same thing I described if I give it too much gas when taking off from a dead stop. The same thing also happens when I shift at a normal shifting RPM(around 3k) and let it go too low on the rpms(under 2k). The guy I bought it from said the EGR valve was messed up(never heard of one of these lol) so I did some research on here, google, and some other mustang dedicated forums. I now pretty know what it is for, haven't really found out where it is/looks like, but will look tomorrow when it's not dark. The guy I bought it from also said he tried cleaning it out but that didn't work, but I'd rather try that and test for the vaccuum pressure myself....... Also, an fyi, the car was sitting for about 3 months before the previous owner had it so the fuel system and spark plugs/wires light dinged in my head.

My question is what do you guys, and gals, think it is/could be? Thanks for all the help in advance and I look forward to learning a lot.
 

Green_NV

New Member
Dec 12, 2007
7
0
0
New Westminster, BC
Dec 14, 2007
#2
  • Dec 14, 2007
  • #2
First thing you should do is a tune up, not because it's going to fix your problems but because you don't know when the last time it has been done. Also, it could fix your problems. Change your oil, oil filter, fuel filter (located right infront of the gas tank on the passenger side), plugs, wires, air filter, etc...

How does the car idle? Pop the hood with it running and listen for a vacuum leak.

Oh and one other thing you can do is go pick up some SeaFoam from NAPA. That stuff works GREAT. Use it before changing the oil because once you add it to your crankcase you won't want to keep that stuff in there for longer then 250 miles.
 
D

dabazied

New Member
Dec 14, 2007
2
0
0
Dec 14, 2007
#3
  • Dec 14, 2007
  • #3
It idles low for what I'm used to in cars(i'm used to the imports @ between 800-1k), at around 600rpm. It takes a little press of the gas to start it sometimes as well. When it I was looking at it, it kept cutting off while idling but haven't tried to check a cold idle since I got home yet. It has been sitting for a couple of weeks though without being cranked.
I'm gonna do a tune up within the next week or 2 'cause I know it needs one, definitely the tell-tale sign is that it hasn't even been inspected n that ran out May 07 lol...... I LOVE sea foam, use it on all of my cars. But do you think that the egr valve thing would be a possible cause for these problems? From doing some reading tonight it looks like that may be a possibility but I was thinking tune-up stuff as well.
 

Green_NV

New Member
Dec 12, 2007
7
0
0
New Westminster, BC
Dec 14, 2007
#4
  • Dec 14, 2007
  • #4
The EGR could, yes...but I'm gunna say that it's not (I've been wrong before though ). Your car should be idling a lot higher then that and you shouldn't have to hit the gas to get it going. My car idles at 1100 with the turbo motor and with the N/A 2.3 that was in there it was around 1000. I would probably say it's gunna be vacuum, maybe the idle air control module, or even the throttle position sensor. I'd just start with the basics though, you might get lucky and just find a broken or popped off vacuum line. Easy enough to find, just listen!

Without actually seeing it though, I couldn't diagnose it. It could even be something like a bad O2 sensor.

I know yours isn't a turbo engine but most of the sensors and the EGR are in the same place as this engine
http://www.turbotbird.com/FaqPage/Engine.jpg
 
E

ethangsmith

Member
Jan 28, 2007
227
0
16
Manheim, PA
Dec 15, 2007
#5
  • Dec 15, 2007
  • #5
If you can get your hands on a Chilton or Haynes manual, that would be an excellent start. It will show you what is what and basics on how to replace it. After you visually inspect things in the engine bay, I would run the codes on it. A repair guide will tell you how to do it. All you need is a voltmeter.
 

Red_LX

I’m not much help unless you’re looking for ****!
Founding Member
Nov 29, 1999
5,896
73
129
Morgantown, WV...where couches meet their doom
Dec 16, 2007
#6
  • Dec 16, 2007
  • #6
Sounds like it could be TFI, also I'm assuming from your post that after you get it going it runs fine? If not, could also be a clogged cat.
 

86crazyhorse

New Member
Mar 22, 2006
29
0
0
clackamas Or
Dec 19, 2007
#7
  • Dec 19, 2007
  • #7
try the timming belt could be off a tooth or 2.
 
You must log in or register to reply here.

Similar threads

Question about my weird timing.
  • 2003 mustang gt modded
  • Apr 22, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
7
Views
149
1996 - 2004 SN95 Mustang -General/Talk- Jun 26, 2026
2003 mustang gt modded
C
1992 LX 2,3, automatic problems, oil dissapears.
  • Carpimp
  • Aug 10, 2025
  • 2.3L (N/A & Turbo) Tech
Replies
2
Views
205
2.3L (N/A & Turbo) Tech Aug 10, 2025
General karthief
C
C4 trans help needed
  • CPH89LX
  • Apr 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
218
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 28, 2026
CPH89LX
C
D
Question about EGR valve, replacement, and a part on the valve.
  • DPP
  • May 9, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
128
SN95 V6 Mustang Tech May 23, 2026
DPP
D
D
66 Coupe Progress Thread
  • DTCRAWLEY
  • Apr 19, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
43
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Jun 17, 2026
DTCRAWLEY
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2.3L (N/A & Turbo) Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?