• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

moved battery to the hatch

  • Thread starter Thread starter MarcMonteverde
  • Start date Start date Sep 20, 2007

MarcMonteverde

New Member
Sep 4, 2006
66
0
0
S@c-ToWn
Sep 20, 2007
#1
  • Sep 20, 2007
  • #1
so i moved my battery to the hatch , my friend told me that im gonna need a kill switch if i go to the track, ive never race'd at the track only watched, but ive seen cobras with the battery in the trunk and never have i seen a kill switch
are their are down falls to puttin the battery in the hatch or is it better?
thanks!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Sep 20, 2007
#2
  • Sep 20, 2007
  • #2
For a battery cut off switch, see
http://www.moroso.com/catalog/categorydisplay.asp?catcode=42225 is the switch
http://www.moroso.com/catalog/images/74102_inst.pdf
Use the super duty switch and the following tech note to wire it and you
will be good to go.

Use the Moroso plan for the alternator wiring and you risk a fire.
The 10 gauge wire they recommend is even less adequate that
the stock Mustang wiring.

There is a solution, but it will require about 40' of 18 gauge green wire.

Wire the battery to the two 1/2" posts as shown in the diagram.

The alternator requires a different approach. On the small alternator plug
there is a green wire. On the diagram it is #904, lt green/red wire that connects
to the alternator and dash light. It is the sense lead that turns the regulator on
when the ignition switch is in the run position. Cut the green wire and solder the
40' of green wire between the two pieces. Use some heat shrink to cover the
splices. See http://fordfuelinjection.com/?p=7 for some excellent
help on soldering & using heat shrink tubing.

Run the green wire back to the Moroso switch and cut off the excess wire.
Try to run the green wire inside the car and protect it from getting cut or
chaffed. Crimp a 18 gauge ring terminal (red is 18 gauge color code for the crimp
on terminals) on each wire. Bolt one ring terminal to each of the 3/16" studs.
Do not add the jumper between the 1/2" stud and the 3/16" stud as shown it the
Moroso diagram.

How it works:
The green/red wire is the ignition on sense feed to the regulator. It supplies
power to the regulator when the ignition switch is in the run position. Turn
the Moroso switch to off, and the sense voltage goes away, the voltage
regulator shuts off and the alternator quits making power.

This setup uses a 125-150 amp fused power lead for a 3G Alternator.
For the stock alternator, you can omit the fuse & 4 gauge wire and use the stock power wire.


See the following website for some help from Tmoss (diagram designer) &
Stang&2Birds (website host) for help on 88-90 wiring and lots more…

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Diagram courtesy of Tmoss and Stang&2birds.



Rear mounted battery ground wiring. Follow this plan and you will have zero
ground problems.


One 1 gauge or 1/0 gauge wire from battery negative post to a clean shiny spot
on the chassis near the battery. Use a 5/16” bolt and bolt it down to make the
rear ground. Use a 1 gauge or 1/0 gauge wire from the rear ground bolt to a clean
shiny spot on the block.

One 4 gauge wire from the block where you connected the battery ground wire to
the chassis ground where the battery was mounted up front. Use a 5/16” bolt
and bolt down the 4 gauge engine to chassis ground, make sure that it the metal
around the bolt is clean & shiny. This is the alternator power ground.

The computer has a dedicated power ground wire with a cylindrical quick connect
(about 2 ½”long by 1” diameter. It comes out of the wiring harness near the
ignition coil & starter solenoid (or relay). Be sure to bolt it to the chassis ground
in the same place as you bolted the alternator power ground. This is an
absolute don’t overlook it item for EFI cars


Picture courtesy timewarped1972


Crimp or even better, solder the lugs on the all the wire. The local auto stereo
shop will have them if the auto parts store doesn't. Use some heat shrink tubing
to cover the lugs and make things look nice.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Sep 20, 2007
#3
  • Sep 20, 2007
  • #3
Its a safety rule basically. So they can easily kill your car if you wreck at the track. It's not hard to wire one in. I have one in my car.
 

87Mustang351

Member
Sep 12, 2005
220
1
16
Canada, Nova scotia, Cape Breton
Sep 20, 2007
#4
  • Sep 20, 2007
  • #4
can anyone give me a step by step on how to do it, i tryed to wire one to mine but i dont think i have it done right..! help plz! a step by step as in how u done it urself not a website thanks!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Sep 20, 2007
#5
  • Sep 20, 2007
  • #5
87Mustang351 said:
can anyone give me a step by step on how to do it, i tryed to wire one to mine but i dont think i have it done right..! help plz! a step by step as in how u done it urself not a website thanks!
Click to expand...

Follow thie instructions I posted.
 

MarcMonteverde

New Member
Sep 4, 2006
66
0
0
S@c-ToWn
Sep 20, 2007
#6
  • Sep 20, 2007
  • #6
okay i get what ur sayin, thanks man!!!!
 
You must log in or register to reply here.

Similar threads

R
Electrical Trunk Mount Battery and Cut Off Switch- Need Help
  • Rcdgl
  • Nov 20, 2024
  • Fox 5.0 Mustang Tech
Replies
1
Views
396
Fox 5.0 Mustang Tech Nov 20, 2024
nickyb
Radio, Speaker Upgrades
  • TripleYellow
  • Apr 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
225
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 24, 2026
TripleYellow
2
Resolved Electrical mayhem
  • 2000ElectricGreen
  • Mar 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
496
1996 - 2004 SN95 Mustang -General/Talk- Sep 4, 2026
2000ElectricGreen
2
G
In expensive ceramic coating
  • gray owl
  • Jul 12, 2026
  • Mustang Sound & Shine All
Replies
7
Views
485
Mustang Sound & Shine All Aug 18, 2026
NotaVegetarian
N
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
603
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?