• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need Help with Ignition Problem

  • Thread starter Thread starter xsvstang
  • Start date Start date Feb 15, 2008
X

xsvstang

New Member
Apr 5, 2001
14
0
0
Feb 15, 2008
#1
  • Feb 15, 2008
  • #1
BACKGROUND
I just swapped in a 3550 for the c4 in the 89 in the signature. Prior to doing that I did not disconnect the battery. During the process of removing the starter I hit the contacts a few times throwing some sparks. I also tacked up my crossmember with a welder after adjusting. I have bypassed the neutral safety switch. No electrical connections to the tranny at this time. The car is carbed and obviously no computer.


THE PROBLEM

Now the car will crank, but not start. The ignition is a msd ready to run distributor with a magnetic pickup and a blaster coil. The coil got very hot while trying to start the car and started sounded like it was sizzling.
I am getting power to the coil, but I am not getting spark from the coil.

WHAT I HAVE TESTED I ran through MSD procedures for testing the pickup in the distributor by measuring ohms and it passed.

The + side of the blaster coil has 10.75 volts.

I have replaced the blaster coil with a new one.
I have checked all my grounds to make sure when I welded I did not fry one.
I checked all the connections under the dash from where I did the pedal swap and everything looks good.

Where else should I be checking?
 
F

facemelter71

New Member
May 29, 2006
60
0
0
cincy
Feb 15, 2008
#2
  • Feb 15, 2008
  • #2
Check dizzy,if the coil is new and has power then the dissy is the one that tells it when to fire.Check that,ive heard bad things about their dissy's.
 
X

xsvstang

New Member
Apr 5, 2001
14
0
0
Feb 15, 2008
#3
  • Feb 15, 2008
  • #3
The only thing to test, according to the msd troubleshooting guide, is the magnetic pickup, which I did test.


...if should have said tested the pickup in the distributor, not coil...it is fixed now.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Feb 17, 2008
#4
  • Feb 17, 2008
  • #4
have you just held a spark plug to the block as u crank the engine over to verify u have spark? with the new coil installed. Or are you still not getting spark from the new coil?
 

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
Feb 17, 2008
#5
  • Feb 17, 2008
  • #5
Are you sure your getting spark? Remember you need air, fuel and spark for a engine to fire... I am missing the point of the tranny change causing the starting issues. I get the neutral safety switch but your cranking now and that problems should be resolved. I also guess beceuase we are assuming it was running before the tranny switch. Did you make the double swap of tranny and ignition?

Allen
 
X

xsvstang

New Member
Apr 5, 2001
14
0
0
Feb 17, 2008
#6
  • Feb 17, 2008
  • #6
The tranny switch should have nothing to do with it, as the car was running prior to the swap. It is only germane as that is when I arced the starter.

I put the old blaster coil on my other mustang. The car started. It is not the coil. This is a 4 cylinder to 408w conversion. The only wires going to the positive side of the coil is the 12v keyed source and the positive from the distributor. The only thing going to the negative post is the tach wire and orange wire from the distributor (per msd ready to run distributor installation)

I left the tach wire off and the car fired when I cranked it. I cranked it again and got a grinding noise as the starter bolt came loose from the bellhousing.

That lovely process wasted the starter.

So I am done troubleshooting until I replace the starter.
 
You must log in or register to reply here.

Similar threads

K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
397
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
J
Engine Tuning...?
  • justadude07
  • May 30, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
397
Fox 5.0 Mustang Tech Aug 21, 2026
Qtrhrse23
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
520
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
485
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
594
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?