• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

New Cats

  • Thread starter Thread starter Lnpr4eva
  • Start date Start date Jul 12, 2006
L

Lnpr4eva

New Member
Jul 11, 2006
1
0
0
Jul 12, 2006
#1
  • Jul 12, 2006
  • #1
First let me say hello to all.. I am new here.. Now I have a question.. I am working on building up my 95 GT 5.0 .. I recently put the Pypes High performance cats on my Stang after my stock went out .. My stang seems to be idling rough when coming to a stop.. It will shake crazy when Im slowing to a stop then stop just a fast as it started, no shaking in neutral just when coming to a stop and on start up, other wise it drives fine.. I didnt have this problem before the new cats were put on.. I was wondering if there is a connection? If not what should I be checking? I just did a complete tune up and oil change and had my fuel inj cleaned.. Im stumped.. Any help would be greatly appreciated. :
 
P

Pennywise2

Banned
May 16, 2006
1,379
1
0
Jul 12, 2006
#2
  • Jul 12, 2006
  • #2
Welcome to the Asylum.
If your idle is that bad than your Idle air control valve
probably needs replacing.If that is the case get a Motorcraft replacement.
 

mo_dingo

20+ Year Stangneter
Aug 26, 2003
3,031
2
58
Tucson, AZ
Jul 12, 2006
#3
  • Jul 12, 2006
  • #3
You might need to reset your computer.

Another thing is to clean your MAF & IAT sensors. They may be causing your problem. And reset the comp after you clean them, especially if they are really nasty.
Scott
 

JJ95GTID

Active Member
Sep 22, 2003
1,141
4
49
Phoenix, AZ
Jul 13, 2006
#4
  • Jul 13, 2006
  • #4
You also might want to see if you have any codes coming up from the ECM. You may have a damaged O2 sensor. You can also check the O2 sensor connectors to see if they are on good.
 

ProKiller

Founding Member
Apr 26, 2002
3,064
15
78
PA
Jul 13, 2006
#5
  • Jul 13, 2006
  • #5
i would check your o2 sensors first to make sure you didn't break them or something. how is the drive quality? usually if your o2s are bad, it won't feel right when you get on it, dogs out, etc. did you do the install? did you touch the sensor ends of the o2s?

by all means clean out your mass air sensor (MAS) and your incoming air temperature (IAS) and your incoming air controller (IAC).
 

1TallMF

New Member
Apr 17, 2006
955
1
0
Montreal
Jul 13, 2006
#6
  • Jul 13, 2006
  • #6
+1 for the IAC, the port on the TB might just be carboned-up. But yeah, try to reset the computer first to see if it helps at all.
 
You must log in or register to reply here.

Similar threads

C
New mustang owner
  • CPH89LX
  • Apr 26, 2026
  • The Welcome Wagon
Replies
3
Views
201
The Welcome Wagon Apr 27, 2026
91AOD5.0LX
L
Exhaust 95 gt pypes catted x pipe
  • Lx5.0fiend
  • Aug 22, 2025
  • 1994 - 1995 Specific Tech
Replies
5
Views
459
1994 - 1995 Specific Tech Sep 18, 2025
revhead347
E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
3
Views
345
2005 - 2009 Specific Tech Sep 26, 2026
manicmechanic007
M
new member
  • markmoon
  • Jul 24, 2026
  • The Welcome Wagon
Replies
1
Views
129
The Welcome Wagon Jul 24, 2026
General karthief
T
Vibrating clutch pedal
  • t.hite10
  • Aug 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
8
Views
237
1996 - 2004 SN95 Mustang -General/Talk- Aug 11, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?