• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

oil on plugs

  • Thread starter Thread starter stevesLX
  • Start date Start date Feb 28, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Feb 28, 2007
#1
  • Feb 28, 2007
  • #1
Guys I just had the whole lower half of my motor rebuilt. New rings bearings seals, had the rods and pistons reconditioned. The heads I had a 3 angle valve job done and they had a clean up cut done on them. I have changed the oil in it and I also pulled the plugs to take a look at them. The back 2 plugs on both sides of the motor which would be #3,4 and 7,8 are wet. When I wipe the threads off of the plugs its a black wet fluid like maybe oil. The electrodes thereselves are a light tanish color. The front 2 plugs on both sides of the motor are dry as a bone though. I only have roughly 250 miles on this thing now. Also I live in Ohio and it has been cold up here and I know when its cold cars smoke out the exhaust like steam but even after I drive this thing for 40 or 50 miles when I pull into work it still has some smoke coming out of the exhaust bon both sides. I hope I am just being paranoid and I am not already having another blow by issue. I know the machine shop will get an ear full if thats the case but I'm sure they would say well we did everything right and you probably screwed something up which I dont know how I would of I have just now started to be a little more aggressive with it. So any help would be appreciated here. I beleive the plugs I am using are motorcraft ASF42C
 

DMAN302

My mom says thanks for the pearl necklace.
Nov 8, 2003
2,120
2
59
windsor, Canada
Feb 28, 2007
#2
  • Feb 28, 2007
  • #2
Rings may not have seated yet....I assume you didn't use synthetic oil for the breakin? Some engines might take some time to stop using some oil. Another option could be bad valve seals on the indicated cylinders but I'd be more inclined to wait a bit and see if the problem persists.
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Feb 28, 2007
#3
  • Feb 28, 2007
  • #3
If it's really cold out, I'm not sure I'd be worried about a little steam (looks like smoke) coming out of the tail pipes even after it's fully warmed up.

If it actually is smoke though, it's possible you've got blowby again. Like DMAN said, your rings may not be seated yet. Just keep driving it, check the oil, and follow any break-in instructions the machine shop gave you.

Are the electrodes on the back 4 plugs wet, or just the threads? How do those electrodes look compared to the front 4 plugs?
 

85ragtop

BTW, I like dudes.
10 Year Member
Nov 29, 1999
823
475
123
NC
Feb 28, 2007
#4
  • Feb 28, 2007
  • #4
That’s an awful lot of oil. The ring should have seated by now, I would think.
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Feb 28, 2007
#5
  • Feb 28, 2007
  • #5
check and make sure that you aren't getting oil sucked in through the PCV and intake. What color is the smoke? Are you using alot of oil? I would give it some time to wear in, and worry about it later.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Feb 28, 2007
#6
  • Feb 28, 2007
  • #6
No my oil level has been just fine and my oil pressure holds at about 70psi on the hywy and 30-40 at idle. It has a high volume oil pump. The electrodes are dry and look pretty close to the other ones. Just the threads are wet. The smoke is white and I had a friend behind me today and he said that when I was sitting at a light it wasn't smoking but as soon as I took off or accelerated it would smoke a little bit.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 28, 2007
#7
  • Feb 28, 2007
  • #7
oil

if its not on the electrodes its more than likely not in the cyinder. have you spilt any oil when filling it? and check valve cover gaskets. if ts just on the threads its coming from outside.
 

85ragtop

BTW, I like dudes.
10 Year Member
Nov 29, 1999
823
475
123
NC
Feb 28, 2007
#8
  • Feb 28, 2007
  • #8
BK_CAULEY said:
if its not on the electrodes its more than likely not in the cyinder. have you spilt any oil when filling it? and check valve cover gaskets. if ts just on the threads its coming from outside.
Click to expand...

Mine leaked from the valve cover and got all over my plugs and my headers.
 
You must log in or register to reply here.

Similar threads

A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
214
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
Who the hell puts the wrong spark plugs in a 3.8L?
  • snowstang
  • Mar 25, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
678
1996 - 2004 SN95 Mustang -General/Talk- Apr 3, 2026
LILCBRA
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
347
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
2
Running very very rich
  • 2esoteric
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
473
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?