• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

PCV Hose Routing on Performer Intake

  • Thread starter Thread starter Beasly B
  • Start date Start date Jan 29, 2006

Beasly B

New Member
Jan 7, 2006
165
0
0
Virginia
Jan 29, 2006
#1
  • Jan 29, 2006
  • #1
I took off my upper intake this morning because I need to set up my rocker arms the right way this time, anyway I bought my edelbrock performer upper and lower used. When I put it on the hose coming from the front with the sharp bend goes into a "T" and then to the pcv, where the "T" fits into the upper intake it was blocked off, so thats the way I left it and blocked off the "T" fitting in the hose where it screws into the upper intake. I removed the plug and installed the fitting back into the upper intake, looking at my picture , can anyone tell if this is the right setup now? Also there was a little bit of oil puddled up in the upper intake when I took off the side cover, could the way it was setup cause this?
 

Attachments

  • 100_2654.webp
    63.5 KB · Views: 163

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Jan 29, 2006
#2
  • Jan 29, 2006
  • #2
At first i got confused, but i think i no what u mean after readinig it a couple times. The T was NOT in the intake, it was just chillen by itself with the bottom of it plugged and it connecting the 2 hoses. and now u put the T back into the intake right? From the picture that is how all the ones Ive seen been set up. The other way would still work but wouldnt be as effective since it only has vacuum source sucking the pcv gases out and has to travel longer into the tube to get into the intake, Rather than now it has 2 possible vacuum sources sucking out the pcv gases. I dont no if it will make a difference but it seems better to me.
 

Beasly B

New Member
Jan 7, 2006
165
0
0
Virginia
Jan 29, 2006
#3
  • Jan 29, 2006
  • #3
thanks for the input ... sorry it was so confusing. what's your opinion on the oil in the upper intake?
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Jan 29, 2006
#4
  • Jan 29, 2006
  • #4
Only thing i can think of is sticking pcv valve or something like that, or the way the guy rigged up the lines before you.
 
You must log in or register to reply here.

Similar threads

Engine Coolant boiling in hose?
  • Teen'93stang5.0
  • Jun 3, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
351
Fox 5.0 Mustang Tech Jun 8, 2026
Mustang5L5
B
Fuel 1990 installing edelBrock intake
  • Beaker
  • Oct 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
340
Fox 5.0 Mustang Tech Oct 6, 2026
Noobz347
H
Engine 1987 5.0 HO vacuum hose locations
  • harryhaber
  • Jun 20, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
630
Fox 5.0 Mustang Tech Jun 21, 2025
limp
S
Mach 1 iac valve in a 4.6 gt
  • solodriverz
  • Jun 3, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
174
SN95 4.6L Mustang Tech Jun 5, 2026
squeak93
Surging/stalling! problem or tune?
  • djj62478
  • Oct 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
404
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 14, 2026
KRUISR
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?