pi heads w/cams

M

must46

New Member

May 31, 2003

6

0

0

gatineau

Mar 3, 2004

#1

• Mar 3, 2004

• #1

hey guys!

I have 96 stang and got 2001 pi heads and i would like to get cams from comps cam but they have 550 lift. I'm not to sure if they would be alright with my block since i have flat piston. If they won't fit wich cam would be best for me. I wanna get something mild for street and strip.

p.s. sorry for my spelling guys i'm from north of quebec canada

 

lman657

New Member

Aug 31, 2003

85

0

0

Mar 3, 2004

#2

• Mar 3, 2004

• #2

no no no!

I am rebuilding my ENGINE right NOW because I put the XE270AH grind in my engine, and it was in time. All 8 pistons hit, eventually breaking 3 valve guides and beating the crap out of 3 combustion chambers.

I'm a bit ticked w/ comp cams, cause I called to see if the cams would clear and he said "you'll have to figure out that on your own buddy."

So, i figured plenty of guys are doing this, so i might as well put in, it should clear. Well, i turned the engine over and it did clear, but it turns out that the lifters had not pumped up, when they pumped up, the intake valves made full lift, and put an ~1mm divot in each piston.

My engine is at the shop right now, and am looking at about $1000-1500 to rebuild this on my own, with the newer dished pistons.

Well thanks for letting me vent.

I believe that you'll have to get the newer pistons, or get the non-pi cams. You might want to look at the cams from VT Engines, they seem to have great service, great cams, and it sounds like a lot of guys are happy with them. I'm sure their customer service knows what's going also...

good luck!

Lance

 

M

must46

New Member

May 31, 2003

6

0

0

gatineau

Mar 3, 2004

#3

• Mar 3, 2004

• #3

thanks for the heads up!
really appriciated before i do something i'm gona regret. I wonder if .500 lift will be ok.

 

dub_c39

New Member

Mar 4, 2003

126

0

0

Ohio

Mar 3, 2004

#4

• Mar 3, 2004

• #4

The stock pi cams are .505/.534-inch lift and they will work just fine. I'm pretty sure that the stock '98 pistons will handle a .550 lift. Pm VTEngine or VTEngines, one of those guys should be able to answer your question ......When you find out, let me know

 

M

must46

New Member

May 31, 2003

6

0

0

gatineau

Mar 4, 2004

#5

• Mar 4, 2004

• #5

So a wild non-pi cam from comp cam will do find since they have .500 lift will they give me that extra power or should i still go with a stock pi cam i got the choice money is no option here.As long as they won't hit my piston

 

dub_c39

New Member

Mar 4, 2003

126

0

0

Ohio

Mar 4, 2004

#6

• Mar 4, 2004

• #6

If it were me, I would call around and and try to get the most wild cam I could find. I think you should look into VT mild cams. They are 540/.550, 224/226, 110/110. Just call VT and ask if they would work for your application The number is 519-245-1164 or visit their website at www.vtengines.com

 

2

2002BLGT

Well-Known Member

Dec 18, 2003

2,945

4

59

Bedford VA

Mar 5, 2004

#7

• Mar 5, 2004

• #7

I would just run the stock PI cams , until you are ready to go into the bottom end and then do the cams and port those heads at that time . stock lift is plenty for headswapped car , you are going to have added compression , the lift difference isnt going to out weigh the cost of the cams , just my .02 cents

 

VTEngine

Founding Member

Nov 4, 2002

364

0

0

Lansing, MI

Mar 5, 2004

#8

• Mar 5, 2004

• #8

Our stage2 n/a cams work fine with flat tops. Been there, and built it before. The comps are having issues becuase of the big duration they're using. It's holding the valves open too long and causing piston to valve issues. Just thought I'd add to this

 

onlyme

Member

May 9, 2003

375

0

17

missouri

Mar 5, 2004

#9

• Mar 5, 2004

• #9

vt

what would a 96-98 gt put out with these mods, stock p.i heads, vt stage 2 cams, stock p.i. intake, accufab plenum, accufab 75mm tbody, prom 87mm maf, k&n cai, 24lb injectors, 190lph pump, autologic chip, steeda pulleys,msd dis-4 ignition with msd coilpacks and wires, longtube headers, catted xpipe, and catback exhaust?

 

NasaGT

Founding Member

Sep 19, 2002

1,993

2

49

Virginia

Mar 5, 2004

#10

• Mar 5, 2004

• #10

VTEngine said:

Our stage2 n/a cams work fine with flat tops. Been there, and built it before. The comps are having issues becuase of the big duration they're using. It's holding the valves open too long and causing piston to valve issues. Just thought I'd add to this

Click to expand...

Striking Comp cams from list of potential cams. Hmmm that leaves VT cams, I guess my decision has been made.

 

M

must46

New Member

May 31, 2003

6

0

0

gatineau

Mar 5, 2004

#11

• Mar 5, 2004

• #11

thanx for they info guys, i know what to buy now from vtengine. I wonder how much is that going to be in canadian money now.